Campbell Hausfeld COM220 Manual Do Utilizador
Appendix A. Changing COM220 Settings
12: Initiate Telecommunications (P97)
1: 22
1: 22
Phone
Modem/9600
Baud
;set baud-rate/modem
2: 5
Disabled when User Flag 5 is High
3: 45
Seconds Call Time Limit
4: 0
Seconds Before Fast Retry
5: 0
Fast
Retries
6: 0
Minutes Before Slow Retry
7: 3
Failures Loc [ Failures ]
8: 222
Callback
ID
;must also enter callback ID in LoggerNet Setup
13: Extended Parameters (P63)
;7-digit phone number
1: 5
Option
2: 5
Option
3: 5
Option
4: 1
Option
5: 2
Option
6: 1
Option
7: 2
Option
8: 13
Option ;13 is the termination character; always place after phone number
End Program
A.4.4 Example Programs for Data-Callbacks via a CR1000
Datalogger Router.
In order to do data callbacks via a datalogger router with COM220 and RF401s
or MD485s, they must all be configured to communicate with one another. In
addition, two programs are necessary: one for the datalogger router and one for
the remote datalogger. Below are example programs for a datalogger router
and a remote datalogger. For these examples, the COM220 is configured for
SDC7 and the router datalogger has the following settings (you can enter
these settings via the datalogger keypad or from the LoggerNet status table):
PakBusAddress = 2, IsRouter = 1 or True, and BeaconSDC8=30, enabling the
router to discover the remote. The remote datalogger’s PakBusAddress = 1.
In addition, the RF401s or MD485s are set for CSDC8 (see the RF401 or
MD485 manual for directions on configuring these devices).
or MD485s, they must all be configured to communicate with one another. In
addition, two programs are necessary: one for the datalogger router and one for
the remote datalogger. Below are example programs for a datalogger router
and a remote datalogger. For these examples, the COM220 is configured for
SDC7 and the router datalogger has the following settings (you can enter
these settings via the datalogger keypad or from the LoggerNet status table):
PakBusAddress = 2, IsRouter = 1 or True, and BeaconSDC8=30, enabling the
router to discover the remote. The remote datalogger’s PakBusAddress = 1.
In addition, the RF401s or MD485s are set for CSDC8 (see the RF401 or
MD485 manual for directions on configuring these devices).
Program for CR1000 Router:
'Router program for data callback via router w/ phone link to LoggerNet
'Phone to MD485 or RF401 w/DL at Base
'Router PakBus Address = 2, IsRouter = 1, BeaconSDC8 = 30 to discover Remote DL which has
PBA = 1
'Router COM220= SDC7; Base RF401 CSDC8; Remote RF401 CSDC8.
'LoggerNet PakBusPort has PBA = 4094
‘ PC-pcMODEM --------COM220sdc7-CR1000(2)-RF401sdc8~~~~~~~~~~~RF401sdc8-CR1000(1)
Public PanelTemperature, BatteryVoltage, DialSuccess
Public Flag(10) AS BOOLEAN
'Phone to MD485 or RF401 w/DL at Base
'Router PakBus Address = 2, IsRouter = 1, BeaconSDC8 = 30 to discover Remote DL which has
PBA = 1
'Router COM220= SDC7; Base RF401 CSDC8; Remote RF401 CSDC8.
'LoggerNet PakBusPort has PBA = 4094
‘ PC-pcMODEM --------COM220sdc7-CR1000(2)-RF401sdc8~~~~~~~~~~~RF401sdc8-CR1000(1)
Public PanelTemperature, BatteryVoltage, DialSuccess
Public Flag(10) AS BOOLEAN
A-11