Chariot Carriers 51100605 Manual Do Utilizador

Rev. 06/13/06 

www.ChariotCarriers.com 

51100605 

 

 •  Use wrist safety strap at all times. 
 •  Always use seat belts. 
 •  Always use parking brake when stroller is stationary. 
 •  Never in-line skate with the Strolling Kit.  A serious accident could occur 

resulting in serious injury or death. 

Initial Assembly Time:  About 5 minutes. 
Tools Required:  A 7/16" and a 1/2" open end or adjustable wrench. 
Note:  Bolts must be securely fastened, but not over tightened. 
 
A. Parking Brake Assembly   Figure 1. 
1.  Place the carrier on a clean surface, turn it upside down so that the 

wheels point upwards, and stand behind the trailer. 

2.  Using a 7/16" wrench, remove the uppermost ¼" locknut from each of the 

two brake bolts.  The brake bolts are the longer bolts, which are the bolts 
closest to the rear of the trailer. 

3.  On the brake assembly, remove the 5/16" locknut from the bolt with the 

exposed threads using a ½" wrench. 

4.  Orient the brake assembly so that the long arms are pointing straight out 

to each side.  The small arm should point towards the rear of the carrier 
and the plastic handle should point downwards, while the Carrier is upside 
down.  Pivot the curved arm so that the plastic handle is on your left hand 
side. 

5.  Place the grommeted end of the wrist safety strap onto the bolt with the 

exposed threads.  Insert the bolt down through the hollow plug at the 
centre of the rear of the Carrier.  Securely fasten the 5/16" locknut onto 
the bolt inside the rear storage compartment using a ½" wrench. 

6.  Place the holes in the long arms down onto the brake bolts from which the 

¼" locknuts were removed and securely fasten the ¼" locknuts onto each 
bolt using a 7/16" wrench.  The secured bolt should extend into the nylon 
portion of the locknut. 

7.  Turn the carrier back over so it is resting on both wheels. 
 
B. Handlebar Assembly  See Parts List Diagram. 
1.  Insert both ends of the handlebar into the aluminum extensions located at 

the upper rear section of the carrier. 

2.  Depress both spring buttons and insert both handlebar ends fully into the 

extensions.  Both spring buttons must 'pop' out the holes located on 
the inner side of the extensions to secure the handlebar into place. 

Note:  The handlebar height is adjustable.  Simply remove the handlebar, 

rotate it 180°, and re-insert the handlebar into the extensions. 

 

 

 
C. Wheel Assembly  See Parts List Diagram. 
1.  Remove the wheel arms or any other kit component from the wheel arm 

attachment bracket.  

2.  Push the button located on the side of the wheel arm attachment bracket 

as far in as possible. This will create an opening for the caster shaft.  

3.  While maintaining the button depressed, slide the stroller caster from the 

bottom up into the wheel arm attachment bracket.  

4.  When fully inserted, release the button and it will return to its closed and 

locked position. To make sure the caster is secured, test by trying to pull 
the caster downwards.  

5.  Repeat with the other wheel.   

 

 

 

Failure to comply with the manufacture's instructions can lead to serious 
injury or death of the passenger/rider. 

OPERATING INSTRUCTIONS 

 

A.  Seat Belt Instructions 
1.  Follow instructions located in your Cabriolet CTS and Corsaire XL owner's 

manual. 

B.  Parking Brake Instructions 
Note:  Any reference to left or right is from the trailer passengers' point of 

view, while inside the carrier. 

1.  Engage parking brake by pivoting the plastic handle of the brake 

assembly, located down low behind the carrier, from the right to the left 
hand side of the carrier until it 'snaps' into place against the frame. 

 
2.  Disengage parking brake by pivoting the plastic handle from the left all the 

way back to the right hand side of the carrier.  The plastic handle must 
rest against the carrier frame to prevent the parking brake from contacting 
the tires. 

WHEEL STORAGE AND STROLLER DISASSEMBLY 

 

1.  To store the wheel on the trailer, turn the wheel assembly upside down 

angled towards the back of the carrier.  

2.  While maintaining the button depressed, slide the wheel down from the 

top of the wheel arm attachment bracket into the opening.  

3.  When fully inserted, release the button and it will return to its closed and 

locked position. To make sure the caster is secured, test by trying to pull 
the caster downwards.  

 
IMPORTANT:

in the foot well of the carrier. At no time should any cargo be stored 
in the rear of the carrier.