Kenwood TS-570S Manual Do Utilizador
9
3 GETTING ACQUAINTED
@6
@6
@6
@6
@6 DSP SLOPE (HIGH) control
In SSB or AM mode, turn to change the high cut-off
frequency of the receive pass band. Use the control to
improve readability of the desired signal when higher
frequency interference is present {page 37}.
frequency of the receive pass band. Use the control to
improve readability of the desired signal when higher
frequency interference is present {page 37}.
@7
@7
@7
@7
@7 DSP SLOPE (LOW) control
In SSB or AM mode, turn to change the low cut-off
frequency of the receive pass band. Use the control to
improve readability of the desired signal when lower
frequency interference is present {page 37}.
frequency of the receive pass band. Use the control to
improve readability of the desired signal when lower
frequency interference is present {page 37}.
@8
@8
@8
@8
@8 RIT/XIT control
After switching ON the RIT or XIT function, turn to
select the desired frequency offset {pages 30, 32}.
select the desired frequency offset {pages 30, 32}.
@9
@9
@9
@9
@9 AF control
Turn to adjust the audio frequency gain {page 13}.
#0
#0
#0
#0
#0 RF control
Turn to adjust the radio frequency gain {page 13}.
#1
#1
#1
#1
#1 IF SHIFT control
Turn to slide the receive pass band either lower or
higher in frequency when interference is present
{page 36}.
higher in frequency when interference is present
{page 36}.
#2
#2
#2
#2
#2 SQL control
Used for muting (“squelching”) the speaker output when
no receive signal is present {page 14}.
no receive signal is present {page 14}.
#3
#3
#3
#3
#3 MULTI/CH control
In VFO mode, turn to step the operating frequency up
or down {page 29}. In memory channel mode, turn to
select a memory channel {page 40}. Also used for
selecting Menu numbers when accessing the Menu
mode {page 16}, and as a selector to choose settings
for various functions activated by front panel buttons.
or down {page 29}. In memory channel mode, turn to
select a memory channel {page 40}. Also used for
selecting Menu numbers when accessing the Menu
mode {page 16}, and as a selector to choose settings
for various functions activated by front panel buttons.
MICROPHONE
q
q
q
q
q UP/DWN buttons
Use these buttons to step up or down the VFO
frequency, memory channels, or Menu selections.
Press and hold down to continuously change the
settings.
frequency, memory channels, or Menu selections.
Press and hold down to continuously change the
settings.
w
w
w
w
w PTT (Push-to-Talk) switch
The transceiver is placed in transmit mode when this
non-locking switch is held down. Releasing the switch
returns the transceiver to receive mode.
non-locking switch is held down. Releasing the switch
returns the transceiver to receive mode.
PTT
DWN
UP
q
w
PF
ATT
PRE-AMP
VOX
PROC
SEND
CH1
MIC
CW
FSK
LSB
USB
FM
AM
AM
AT TUNE
HF TRANSCEIVER TS-570D
PHONES
1
CH2
2
CH3
3
ANT
4
REC
5
FINE
6
NB
7
AGC/TONE
8
REV
9
CLR
F.LOCK
0
ENT
MIC
PWR
KEY
DELAY
MENU
1MHz
SPLIT
M/V
DOWN
UP
MR
TF-SET
A=B
SCAN
M>VFO
M.IN
M.IN
FILTER
CW TUNE
B.C.
N.R.
A/B
CLEAR
RIT
XIT
RIT/XIT
IF SHIFT
SQL
CH
4
6
0
10
2
8
AF
RF
LO
W
C
U
T
HIGH
DSP SLOPE
LOW
4
6
0
10
2
8
+
–
@6
@7
#0
@9
#1
#2
#3
@8