Thermador PCG36 Instrução De Instalação
English 2
Safety Instructions
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
APPROVED FOR ALL RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
Before you Begin
IMPORTANT: Save these Instructions for the Local
Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit
for the owner.
OWNER: Please retain these instructions for future
reference.
Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit
for the owner.
OWNER: Please retain these instructions for future
reference.
WARNING:
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult a
qualified installer, service agency, manufacturer
(dealer) or the gas supplier.
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information consult a
qualified installer, service agency, manufacturer
(dealer) or the gas supplier.
NOTE:
This Cooktop is NOT designed for installation in
manufactured (mobile) homes or for installation in
Recreational Park Trailers.
This Cooktop is NOT designed for installation in
manufactured (mobile) homes or for installation in
Recreational Park Trailers.
DO NOT install this appliance outdoors.
Data Rating Plate
Cooktop Models:
The data rating plate showing the model and serial
numbers of your cooktop is located on the underside of the
cooktop chassis near the gas inlet connection and electric
power cord. This information is required if customer service
is requested. Before installation, the model and serial
numbers should be entered in the appropriate spaces in
the "BEFORE CALLING FOR SERVICE" section near the
back of the Care and Use Manual. After installation,
accessing the information is difficult.
numbers of your cooktop is located on the underside of the
cooktop chassis near the gas inlet connection and electric
power cord. This information is required if customer service
is requested. Before installation, the model and serial
numbers should be entered in the appropriate spaces in
the "BEFORE CALLING FOR SERVICE" section near the
back of the Care and Use Manual. After installation,
accessing the information is difficult.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE
PROCEEDING
PROCEEDING
IMPORTANT: LOCAL CODES VARY. INSTALLATION,
ELECTRICAL CONNECTIONS, GAS CONNECTIONS,
ELECTRICAL CONNECTIONS, GAS CONNECTIONS,
AND GROUNDING MUST COMPLY WITH ALL
APPLICABLE CODES.
APPLICABLE CODES.
Electrical Power Supply
30'' Model:
4 Burners - 120 VAC, 60 Hz., 1 Ph., 10 Amp circuit
4 Burners - 120 VAC, 60 Hz., 1 Ph., 10 Amp circuit
36" Models:
6 Burners - 120 VAC, 60 Hz., 1 Ph., 10 Amp circuit
4 Burners with Electric Griddle - 120 VAC, 60 Hz., 1 Ph., 15
Amp circuit
6 Burners - 120 VAC, 60 Hz., 1 Ph., 10 Amp circuit
4 Burners with Electric Griddle - 120 VAC, 60 Hz., 1 Ph., 15
Amp circuit
48" Model:
6 Burners with Electric Griddle - 120 VAC, 60 Hz., 1 Ph., 15
Amp circuit
6 Burners with Electric Griddle - 120 VAC, 60 Hz., 1 Ph., 15
Amp circuit
Gas Supply
Natural Gas – 6” min. to 14” max. water column (14.9 mb
to 34.9 mb)
Propane Gas – 11”min. to 14”max. water column (27.4 mb
to 34.9 mb)
to 34.9 mb)
Propane Gas – 11”min. to 14”max. water column (27.4 mb
to 34.9 mb)
WARNING
Disconnect power before installing.
Before turning power ON, be sure that all
controls are in the OFF position.
Before turning power ON, be sure that all
controls are in the OFF position.
All sealed burners are rated at 18,000 BTU/HR (*15,000
BTU/HR on LP). *All models are convertible to LP/Propane
gas using an accessory conversion kit.
BTU/HR on LP). *All models are convertible to LP/Propane
gas using an accessory conversion kit.
IMPORTANT
•
A backguard must be utilized when there is less than a
12" horizontal clearance between combustible
materials and the back edge of the cooktop. The
Thermador Low Back backguard must be ordered
separately and installed at the rear of the cooktop. For
island installations and other installations with more
than 12" clearance, an optional stainless steel Island
Trim is available to cover the backguard mounting
flanges.
12" horizontal clearance between combustible
materials and the back edge of the cooktop. The
Thermador Low Back backguard must be ordered
separately and installed at the rear of the cooktop. For
island installations and other installations with more
than 12" clearance, an optional stainless steel Island
Trim is available to cover the backguard mounting
flanges.
•
Verify that the appliance is correct for the type of gas
being provided. Refer to “Step 4: Gas Requirements
and Hookup” on page 11 before proceeding with the
installation.
being provided. Refer to “Step 4: Gas Requirements
and Hookup” on page 11 before proceeding with the
installation.