Whirlpool RF364BXG Manual Do Utilizador
17
To Remove:
1.
Open the oven door. Insert door removal pins, included with
your range, into both hinge hangers. Do not remove the pins
while the door is removed from the range.
your range, into both hinge hangers. Do not remove the pins
while the door is removed from the range.
2.
Carefully close the door until it rests against the door removal
pins.
pins.
3.
Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
the door and your thumbs on the inside surface.
4.
Pull door straight up, then toward you. Hinge hangers will
slide out of front frame hinge slot. Do not remove door
removal pins until the door is replaced on the range.
slide out of front frame hinge slot. Do not remove door
removal pins until the door is replaced on the range.
To Replace:
1.
Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
the door and your thumbs on the inside surface.
2.
Hold oven door so that the top edge of each hinge hanger is
horizontal. Insert hinge hangers into the front frame hinge
slots.
horizontal. Insert hinge hangers into the front frame hinge
slots.
3.
Tilt top of door toward range. Slide hinge hangers down onto
front frame support pins. Make sure the hinge hangers are
fully seated and engaged on the support pins.
front frame support pins. Make sure the hinge hangers are
fully seated and engaged on the support pins.
4.
Insert the door stop clip with the angular surface at the top of
the frame hinge slot, then push in the bottom of the clip until
flanges are flush with the front frame.
the frame hinge slot, then push in the bottom of the clip until
flanges are flush with the front frame.
5.
Open the door completely and remove the door removal pins.
Save door removal pins for future use.
Save door removal pins for future use.
6.
Close the door.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
cost of an unnecessary service call.
Nothing will operate
■
Is the power supply cord unplugged?
Plug into a grounded 3 prong outlet.
Plug into a grounded 3 prong outlet.
■
Has a household fuse been blown or has the circuit
breaker been tripped?
Replace the fuse or reset the circuit.
breaker been tripped?
Replace the fuse or reset the circuit.
Cooktop will not operate
■
Is the control knob set correctly?
Push in knob before turning to a setting.
Push in knob before turning to a setting.
■
On ceramic glass models, is the “Cooktop Lockout” set?
See “Cooktop Lockout” section.
See “Cooktop Lockout” section.
■
On coil element models, is the element inserted properly?
See “Coil Elements and Burner Bowls” section.
See “Coil Elements and Burner Bowls” section.
Excessive heat around cookware on cooktop
■
Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area.
Oven temperature too high or too low
■
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
See “Oven Temperature Control” section.
Oven Indicator Lights Flash
■
Do the OVEN ON and OVEN HEATING indicator lights
flash?
See “Assistance or Service” section.
flash?
See “Assistance or Service” section.
■
Do the OVEN HEATING and DOOR LOCKED/CLEANING
indicator lights flash?
The door locked has failed. See “Assistance or Service”
sections.
indicator lights flash?
The door locked has failed. See “Assistance or Service”
sections.
Self-Cleaning cycle will not operate
■
Is the oven door open?
Close the oven door all the way.
Close the oven door all the way.
■
Has the function been entered or have the controls been
properly set?
See “Self-Cleaning Cycle” section.
properly set?
See “Self-Cleaning Cycle” section.