GE 197D4613P004 Utilização E Cuidado
Installing the beverage center/wine chiller.
4
Removing the Packaging
Before using the beverage center/wine chiller, be sure all packing materials and tape
have been removed, including the protective film covering the control and any film
protecting the cabinet.
have been removed, including the protective film covering the control and any film
protecting the cabinet.
If you are discarding an old refrigeration product, remove the doors to reduce
the danger of children being trapped inside.
the danger of children being trapped inside.
To raise the appliance
■
The beverage center/wine chiller can be
freestanding or can be installed under
the counter, with proper clearances.
freestanding or can be installed under
the counter, with proper clearances.
■
Allow the following clearances for ease
of installation, proper air circulation
and electrical connections:
of installation, proper air circulation
and electrical connections:
Each side
1/2
″ (12,7 mm)
Top
2
″ (51 mm)
Back
2
″ (51 mm)
■
Before connecting the appliance
to the power source, let it stand upright
for approximately 2 hours. This will
reduce the possibility of a malfunction
in the cooling system from handling
during transportation.
to the power source, let it stand upright
for approximately 2 hours. This will
reduce the possibility of a malfunction
in the cooling system from handling
during transportation.
■
Do not install the beverage center/
wine chiller where the temperature
will go below 55°F (12,7°C) or above
90°F (32,2°C). If the room temperature
is below the temperature setting, the
beverage center/wine chiller will not
operate (for instance, if the room is
at 55°F (12,7°C) and the setting is 60°F
(15,6°C), the unit will not run).
wine chiller where the temperature
will go below 55°F (12,7°C) or above
90°F (32,2°C). If the room temperature
is below the temperature setting, the
beverage center/wine chiller will not
operate (for instance, if the room is
at 55°F (12,7°C) and the setting is 60°F
(15,6°C), the unit will not run).
■
Install it on a level floor.
■
Do not install the beverage center/wine
chiller where it will be subject to direct
sunlight, heat or moisture.
chiller where it will be subject to direct
sunlight, heat or moisture.
■
Do not store or install this appliance
outdoors.
outdoors.
Installation Guidelines
Adjustable legs at the front corners
of the beverage center/wine chiller
should be set so the beverage center/
wine chiller is firmly positioned on the
floor, with a 1/8
of the beverage center/wine chiller
should be set so the beverage center/
wine chiller is firmly positioned on the
floor, with a 1/8
″ tilt to the back to help
the door closure.
To adjust the leveling legs, turn the legs
counterclockwise to raise the beverage
center/wine chiller, clockwise to lower it.
counterclockwise to raise the beverage
center/wine chiller, clockwise to lower it.
Leveling Legs
C
o
n
su
m
e
r
S
u
p
p
o
rt
T
ro
u
b
le
sh
o
o
ti
n
g
T
ip
s
O
p
e
ra
ti
n
g
In
st
ru
c
ti
o
n
s
S
a
fe
ty
In
st
ru
c
ti
o
n
s
In
st
a
ll
a
ti
o
n
In
st
ru
c
ti
o
n
s
C
a
re
a
n
d
C
le
a
n
in
g
The door handle and screws are shipped
in a hardware bag attached to one
of the shelves inside the cabinet.
in a hardware bag attached to one
of the shelves inside the cabinet.
Locate the door handle and two screws.
Secure the door handle to the side
of the door as shown.
Secure the door handle to the side
of the door as shown.
Door Handle
Screw
Door
Handle