Honeywell F76S Manual Do Utilizador
F76S WATER FILTERS AND MV876B AUTOMATIC-BACKWASH CONTROLS
5
62-3015—4
Commercial and Industrial Installations
(1-1/2 and 2 in. models)
(1-1/2 and 2 in. models)
Commercial and industrial installations have high flow
requirements. For proper operation, limit flow across the F76S
screen. For example, a two-inch pipe may have a 120 gpm flow
at 12 fps linear velocity across a clean screen. High linear
velocity impacts dirt deeply into the screen, making it difficult to
backwash and causing the screen to plug up quickly. In these
situations, install multiple F76 filters in parallel. See Fig. 3.
requirements. For proper operation, limit flow across the F76S
screen. For example, a two-inch pipe may have a 120 gpm flow
at 12 fps linear velocity across a clean screen. High linear
velocity impacts dirt deeply into the screen, making it difficult to
backwash and causing the screen to plug up quickly. In these
situations, install multiple F76 filters in parallel. See Fig. 3.
Fig. 3. Parallel installation of three F76S Water Filters.
Advantages of parallel installation:
•
•
Increased cleaning capacity. Backwash interval is reduced.
•
Elimination of system downtime. Can backwash one F76S
while the others maintain required flow.
while the others maintain required flow.
Another consideration in commercial and industrial
installations is the backwash interval. Because of the high flow
requirements, screens need cleaning on a regular basis. An
MV876 Automatic-Backwash Control can be installed to back-
wash the F76S automatically.
installations is the backwash interval. Because of the high flow
requirements, screens need cleaning on a regular basis. An
MV876 Automatic-Backwash Control can be installed to back-
wash the F76S automatically.
INSTALLATION
CAUTION
Equipment Damage Hazard.
Excessive pressure or temperature can damage
the device.
Ensure water temperature and pressure are below
maximum ratings specified.
Excessive pressure or temperature can damage
the device.
Ensure water temperature and pressure are below
maximum ratings specified.
CAUTION
Equipment Damage Hazard.
Excessive heating can damage internal parts.
Before sweating, separate the tailpieces and nuts from
the filter body.
Excessive heating can damage internal parts.
Before sweating, separate the tailpieces and nuts from
the filter body.
F76S
When installing an F76S, use the following procedure:
1.
Shut off water supply by closing the water supply valve.
2.
Install the F76S in the water line with the arrow pointing
in the direction of water flow.
in the direction of water flow.
3.
Install pressure gauge in the F76S center port (see Fig. 4).
IMPORTANT
When using an MV876, stop here and install the MV876.
4.
Ensure the F76S air vent is open.
5.
Slowly open the water supply valve.
6.
Once the F76S sump fills with water, close the air vent
and fully open the water supply valve.
and fully open the water supply valve.
Fig. 4. Installing the F76S.
MV876
When adding an MV876 to an existing F76, the procedure can
vary depending on the F76 model.
vary depending on the F76 model.
Installation on an F76S
1.
Open the backwash outlet ball valve.
2.
Remove the backwash outlet handle.
3.
Install the MV876. See Fig. 5 and 6.
NOTE:
When you rotate the MV876, it closes the
backwash outlet ball valve.
backwash outlet ball valve.
4.
Ensure the F76S air vent is open.
5.
Slowly open the water supply valve.
6.
Once the F76S sump fills with water, close the air vent
and fully open the water supply valve.
and fully open the water supply valve.
7.
Program the desired backwash interval by pushing the
program button until the desired interval number
appears in the display.
program button until the desired interval number
appears in the display.
100
150
50
0
200
Honeywell
Braukmann
Braukmann
INLET
PIPE
PIPE
M17360
100
150
50
0
200
Honeywell
Braukmann
Braukmann
ISOLATION VALVE.
1
1
1
1
1
100
150
50
0
200
Honeywell
Braukmann
100
150
50
0
200
Honeywell
Braukmann
M16480