Citizen CL-E730 Manual Do Utilizador
43
Chapter 2 Printer Operation
Top Menu
Sub Menu
Default
Menu
Remarks
After Print
Auto Configure
[Auto Config]
[Auto Config]
On
On
Off
Off
Automatically configures optional devices.
On .....AutoConfigure enabled (Regardless
On .....AutoConfigure enabled (Regardless
of whether Function Select is set, if
a peeler or cutter is installed, each
mode is set automatically.)
a peeler or cutter is installed, each
mode is set automatically.)
Off ....AutoConfigure disabled (A peeler of
cutter is installed, but to not operate
the peeler or cutter, turn it Off and
the operation is selected by Function
Select.)
the peeler or cutter, turn it Off and
the operation is selected by Function
Select.)
Function Select
[Function Sel]
[Function Sel]
Tear
Off
Tear
Peel On *
Cut On **
Tear
Peel On *
Cut On **
Selects the operation when the
AutoConfigure is set to Off.
Designates the paper position based on
each option. The operation of this device is
enabled during selection.
At the same time, the parameters of the f
command of Prodigy Plus are emulated for
each optional device.
AutoConfigure is set to Off.
Designates the paper position based on
each option. The operation of this device is
enabled during selection.
At the same time, the parameters of the f
command of Prodigy Plus are emulated for
each optional device.
Cutter Action **
Backfeed
Backfeed
Through
Through
Cutter operating method setting
Backfeed: it feeds back after each cutting
operation.
Through: when the number copied = n, the
back end of sheet 1 to n-1 passes through,
and the back end of the final page that is a
single sheet is copied and fed back.
Backfeed: it feeds back after each cutting
operation.
Through: when the number copied = n, the
back end of sheet 1 to n-1 passes through,
and the back end of the final page that is a
single sheet is copied and fed back.
Peel Wait Delay *
0.1 sec
0.1 to 2.0 sec
Sets the Peel Wait Delay.
Displays only machines with a peeler
installed.
Displays only machines with a peeler
installed.
Paper Position
0.00inch
0.00mm
0.00mm
Peel/Cut/Tear Off
0.00 to 2.00 inch
0.0 to 50.8 mm
Peel/Cut/Tear On
-1.00 to 1.00 inch
-25.4 to 25.4 mm
0.00 to 2.00 inch
0.0 to 50.8 mm
Peel/Cut/Tear On
-1.00 to 1.00 inch
-25.4 to 25.4 mm
Adjusts the stop position. It is based on the
inch/millimeter setting. There are initial
values of the stop position for each device
set above, and later, relative values are set.
inch/millimeter setting. There are initial
values of the stop position for each device
set above, and later, relative values are set.
Menu Key Action
Enters Menu
Repeat Last Set
Repeat Last One
Enters Menu
Repeat Last One
Enters Menu
Sets the menu key action.
Repeat Last Set:
Repeat Last Set:
Repeats the number of copies.
Repeat Last One:
Last one is issued only for the final page.
In the case of a count, afterwards, only
last one is issued.
In the case of a count, afterwards, only
last one is issued.
Enters Menu:
Enters the menu setup mode.
Note: Hold down the MENU key for at least
4 seconds in order to enter the Menu Setup
Mode when setting the “Repeat Last Set” or
“Repeat Last One” menus.
4 seconds in order to enter the Menu Setup
Mode when setting the “Repeat Last Set” or
“Repeat Last One” menus.
* Only when peeling option is mounted.
** Only when cutter is mounted.
** Only when cutter is mounted.
Mode Settings
[Datamax® Emulation]
[Datamax® Emulation]