Frigidaire FHWC3060LS Manual Do Proprietário
8
GB
fig.
9.8”
9.3”
9.13”
0.9”
Long
screws
Wood
screws
10”
9.8”
7.5”
Ceiling
Wall
Dimension
A
(see table)
Desired range hood distance above a
36” high cook top
36” high cook top
Ceiling height
8 Feet
9 Feet
10 Feet *
1
A*
2
A*
2
A*
2
26”*
3
28-3/32”
27”*
3
29-3/32”
28”*
3
30-3/32”
30-3/32”
29”*
3
31-3/32”
31-3/32”
31-3/32”
30”*
3
32-3/32”
32-3/32”
32-3/32”
31”*
3
33-3/32”
33-3/32”
33-3/32”
32”*
3
34-3/32”
34-3/32”
34-3/32”
33”
35-3/32”
35-3/32”
34”
36-3/32”
36-3/32”
35”
37-3/32”
37-3/32”
*
1
: with 10’ extension chimney kit FHW10X60LS
(16) (not supplied). Please call Frigidaire at
1.800.944.9044 to order this kit.
*
1.800.944.9044 to order this kit.
*
2
: “
Dimension A
” in the chart represents the height
from cook top to where the bottom screw mounting
holes would be located.
*
holes would be located.
*
3
: Recommended mounting height
Step 2:
• Install the range hood (1) either with wood screws
• Install the range hood (1) either with wood screws
or long screws, depending on the wall type:
Wall type
Required screws
Wood
4 wood screws (14)
Brick/Concrete
4 long screws (10)
fig.
Electrical connections
Step 5:
• Loosen the 2 short screws from the junction box
• Loosen the 2 short screws from the junction box
(fig. ).
• Connect the incoming positive, neutral and
ground cables to the respective terminals. The
ground cable is already pre-assembled onto the
junction box to provide grounding (fig. ).
ground cable is already pre-assembled onto the
junction box to provide grounding (fig. ).
• Insert 2 screws (10 or 14) in the top location, but
do not fully insert the screws (fig. ). Mount the
range hood (1) to the wall and tighten the screws.
Insert and tighten the 2 remaining screws on the
bottom location of the range hood (fig. / ).
range hood (1) to the wall and tighten the screws.
Insert and tighten the 2 remaining screws on the
bottom location of the range hood (fig. / ).
• Attach the collar (6) to the range hood (1). Secure
with 2 short screws (12) (fig.
).
0.08”
0.08”
fig.
fig.
fig.
fig.
fig.
NOTE
Sometimes, sponge tape covers the holes. If the
holes are located behind the sponge tape, simply
insert the screw through the sponge tape.
holes are located behind the sponge tape, simply
insert the screw through the sponge tape.
Step 3:
• Mount the glass cover (2) onto the range hood
• Mount the glass cover (2) onto the range hood
(1). Use the allen key (13) to secure with 4 sets of
bolts, rubber washers, and washers (9) (fig. ).
bolts, rubber washers, and washers (9) (fig. ).
fig.
Step 4:
• Mount upper and lower brackets (4, 5) on the
• Mount upper and lower brackets (4, 5) on the
wall. Secure with the remaining 4 sets of long
screws (10). The notches of the lower bracket
should be facing up towards the ceiling (fig. ).
screws (10). The notches of the lower bracket
should be facing up towards the ceiling (fig. ).
• Attach the exhaust duct (fig. ).
Installing the hood
Installing the hood
00-Elux FHWC3060LSA-Range hood-Book-01.indd 8
12/8/10 12:43 PM