Ricoh IS 2225 Manual Do Utilizador
Copying from the Bypass Tray
27
2
Copying from the Bypass Tray
Use the bypass tray to copy onto spe-
cial paper such as OHP transparen-
c i e s , t h i c k p a p e r ( p o s t c a r d s ,
envelopes, etc.), adhesive label paper,
thin paper , and copy paper that can-
not be loaded in the paper trays.
cial paper such as OHP transparen-
c i e s , t h i c k p a p e r ( p o s t c a r d s ,
envelopes, etc.), adhesive label paper,
thin paper , and copy paper that can-
not be loaded in the paper trays.
Preparation
When copying from the bypass
tray, select [1 Sided] for copying in
[Dup. / Combine / Series]
When copying from the bypass
tray, select [1 Sided] for copying in
[Dup. / Combine / Series]
(for exam-
ple [1 Sided] → [1 Sided] or [2 Sided]
→ [1 Sided]).
Note
❒ The machine can automatically de-
tect the following sizes as standard
size copy paper:
size copy paper:
❒ Select the paper size when making
horizontal copies.
❒ If you non-standard size copy pa-
per or special paper, you should
input its vertical and horizontal di-
mensions directly. See p.17 “Plac-
ing custom size originals”. The
sizes you can input are as follows:
input its vertical and horizontal di-
mensions directly. See p.17 “Plac-
ing custom size originals”. The
sizes you can input are as follows:
❒ When copying onto OHP transpar-
encies or paper heavier than 128
g/m
g/m
2
(about 34 lb.), you need to
specify the paper type. See p.29
“When copying onto special pa-
per” .
“When copying onto special pa-
per” .
❒ You must specify paper size when
using paper (tracing paper, etc.) of
less than 59g/m
less than 59g/m
2
thickness.
❒ The maximum number of sheets
you can load at the same time de-
pends on paper type. The maxi-
mum number of sheets should not
exceed the upper limit.
pends on paper type. The maxi-
mum number of sheets should not
exceed the upper limit.
❒ Some kinds of envelope might
cause misfeed and wrinkle. If this
happens, push down the fusing
unit's green lever. See p.24 “Enve-
lopes”. Also, be sure to place the
front face of the envelope down-
ward.
happens, push down the fusing
unit's green lever. See p.24 “Enve-
lopes”. Also, be sure to place the
front face of the envelope down-
ward.
❒ Paper of 433 mm (17.0") in length,
or larger, is likely to jam, crease, or
not feed in properly.
not feed in properly.
❒ When copying onto envelopes, see
p.24 “Envelopes”
A
Open the bypass tray.
Metric
version
version
A3L A4K, A4L, A5L, 8" ×
13"L, B4 JISL, B5 JISK, B5
JISL, B6 JISL
13"L, B4 JISL, B5 JISK, B5
JISL, B6 JISL
Inch
version
version
11" × 17"L, 8
1
/
2
" × 14"L,
8
1
/
2
" × 11"L, 5
1
/
2
" × 8
1
/
2
"L,
10" × 14"L
Metric
version
version
• Vertical: 90.0 – 297.0 mm
• Horizontal: 148.0 – 600.0 mm
Inch
version
version
• Vertical: 3.55" – 11.69"
• Horizontal: 5.83" – 23.62"
RuC4_AE_Copy-F_FM_forPaper.book Page 27 Thursday, April 14, 2005 1:21 PM