ZyXEL Communications P-312 Manual Do Utilizador
P312 Broadband Security Gateway
Remote Node Setup
4-9
between 1 and 15. In practice, 2 or 3 is usually a good number.
Private
This parameter determines if the Prestige will include the route to this
remote node in its RIP broadcasts. If set to Yes, this route is kept
private and not included in RIP broadcast. If No, the route to this
remote node will be propagated to other hosts through RIP broadcasts.
remote node in its RIP broadcasts. If set to Yes, this route is kept
private and not included in RIP broadcast. If No, the route to this
remote node will be propagated to other hosts through RIP broadcasts.
Yes/No
RIP
Press the [SPACE BAR] to select the RIP direction from Both/
None/In Only/Out Only and None.
None/In Only/Out Only and None.
None
(default)
Version
Press the [SPACE BAR] to select the RIP version from RIP-1/RIP-
2B/RIP-2M.
2B/RIP-2M.
RIP-1
Multicast
IGMP (Internet Group Multicast Protocol) is a session-layer protocol
used to establish membership in a Multicast group. The Prestige
supports both IGMP version 1 (IGMP-v1) and IGMP-v2. Press the
space bar to enable IP Multicasting or select None to disable it. See the
previous Part for more information on this feature.
used to establish membership in a Multicast group. The Prestige
supports both IGMP version 1 (IGMP-v1) and IGMP-v2. Press the
space bar to enable IP Multicasting or select None to disable it. See the
previous Part for more information on this feature.
None
Once you have completed filling in the Network Layer Options Menu, press [Enter] to return to Menu 11.
Press [Enter] at the message [Press ENTER to Confirm...] to save your configuration, or press [Esc] at
any time to cancel.
Press [Enter] at the message [Press ENTER to Confirm...] to save your configuration, or press [Esc] at
any time to cancel.
4.2.2 Editing TCP/IP Options (with PPPoE Encapsulation)
Make sure that Encapsulation is set to PPPoE in Menu 11.1. Then move the cursor to the Edit IP field in
Menu 11.1, press the [SPACE BAR] to toggle No to Yes. Press [Enter]
Menu 11.1, press the [SPACE BAR] to toggle No to Yes. Press [Enter]
to open Menu 11.3 - Network
Layer Options. The menu and fields are the same as described for PPTP encapsulation above.
4.3 Remote Node Filter
Move the cursor to the field Edit Filter Sets in Menu 11.1, then press the [SPACE BAR] to toggle and set
the value to YES. Press [ENTER] to open Menu 11.5 – Remote Node Filter.
Use Menu 11.5 to specify the filter set(s) to apply to the incoming and outgoing traffic between this remote
node and the Prestige and to prevent certain packets from triggering calls. You can specify up to 4 filter sets
separated by a comma, e.g., 1, 5, 9, 12, in each filter field. Note that spaces are accepted in this field. For
more information on defining the filters, please refer to the chapter on filters. Note that for PPPoE or
PPTP encapsulation, you can also specify remote node call filter sets.
the value to YES. Press [ENTER] to open Menu 11.5 – Remote Node Filter.
Use Menu 11.5 to specify the filter set(s) to apply to the incoming and outgoing traffic between this remote
node and the Prestige and to prevent certain packets from triggering calls. You can specify up to 4 filter sets
separated by a comma, e.g., 1, 5, 9, 12, in each filter field. Note that spaces are accepted in this field. For
more information on defining the filters, please refer to the chapter on filters. Note that for PPPoE or
PPTP encapsulation, you can also specify remote node call filter sets.