Royal Sovereign RSC-1400L Manual Do Utilizador
18
17
RSC -1400L
15. SPECIFICATIONS
Description
RSC-1400L
Power supply
AC 100, 200, 220~240V 50/60Hz 120V 60Hz
Power consumption
100W
Max laminating width
1400mm / 55"
Film thickness
60~500 mic / 1~15mil
Max laminating speed
5m/min / 16.4ft/min
Ready time
Not applicable
Heating method
None
Driving motor
DC geared
Max Temperature control
Not applicable
Speed control
9 settings
Transport type
2 Roller
Film core size
Auto grip (2",3")
Cross cutter
Yes
Hot lamination
No
Cold lamination
Yes
Mounting thickness
15mm / 0.6"
Take up system
Chain link to main motor
Reverse
Yes
Remote control
Yes
Foot pedal
Yes
Unit dimensions
1710
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
650
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
1210 (mm)
(w x d x h)
67.5"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
21.5"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
47.5"
Unit weight
210
kg /
462.9
bs
Carton dimensions
1960
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
900
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
850(mm)
(w x d x h)
77"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
35.5"
?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h
33.5"
Gross Weight
292
kg /
643.7
lbs
13. MAINTENANCE
14. TROUBLESHOOTING
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
comes first.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
may also damage the rollers.
Symptom
Cause
Possible Solution
Machine will not turn
on:
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
b. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
up:
a. Did not raise the temperature.
a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
b. Loosen the bottom roll film tension.