Roberts Gorden HE30UT Manual Do Utilizador
B
LACKHEAT
®
HE I
NSTALLATION
O
PERATION
AND
S
ERVICE
M
ANUAL
4 of 73
SECTION 2: INSTALLER RESPONSIBILITY
• To install the heater, as well as the gas and electrical
supplies, in accordance with applicable specifications
and codes. Roberts-Gordon LLC recommends the
installer contact a local Building Inspector or Fire
Marshal for guidance.
and codes. Roberts-Gordon LLC recommends the
installer contact a local Building Inspector or Fire
Marshal for guidance.
• To use the information given in a layout drawing and
in the manual together with the cited codes and
regulations to perform the installation.
regulations to perform the installation.
• To install the heater in accordance with the
clearances to combustibles.
• To furnish all needed materials not furnished as
standard equipment.
• To plan location of supports.
• To provide access to burners for servicing on all
sides, for burner removal.
• To provide the owner with a copy of this Installation,
Operation and Service Manual.
• To never use heater as support for ladder or other
access equipment and never hang or suspend
anything from heater.
anything from heater.
• To ensure there is adequate air circulation around the
heater and to supply air for combustion, ventilation
and distribution in accordance with local codes.
and distribution in accordance with local codes.
• To safely and adequately install heater using materi-
als with a minimal working load of 33 kg.
• To ensure the heater is placed in an approved
application.
2.1 Low Level User Instructions
In all situations, clearances to combustibles must be
maintained. Signs should be posted in storage areas to
specify the maximum stacking height of items placed
below heater to maintain required clearances to
combustibles. Minimum clearances must be maintained
from vehicles parked below the heater. Caution should be
used when running the system near combustible
materials such as wood, paper, rubber, etc. Consideration
should be given to partitions, storage racks, hoists,
building construction, etc.
maintained. Signs should be posted in storage areas to
specify the maximum stacking height of items placed
below heater to maintain required clearances to
combustibles. Minimum clearances must be maintained
from vehicles parked below the heater. Caution should be
used when running the system near combustible
materials such as wood, paper, rubber, etc. Consideration
should be given to partitions, storage racks, hoists,
building construction, etc.
A laminated wall tag is available for the heater as a
permanent reminder of the safety instructions and the
importance of the required clearances to combustibles.
Please contact Roberts-Gordon or your ROBERTS
GORDON
permanent reminder of the safety instructions and the
importance of the required clearances to combustibles.
Please contact Roberts-Gordon or your ROBERTS
GORDON
®
independent distributor to obtain the wall tag.
Affix the tag by peeling off the backing of the adhesive
strips on the rear surface and position the tag on a wall
near the heater (e.g. thermostat).
strips on the rear surface and position the tag on a wall
near the heater (e.g. thermostat).
A copy of the wall tag (P/N 91037912) is illustrated on the
back cover. This copy of the wall tag can be affixed on the
wall near the heater. Know your model number and
installed configuration. Model number and installed
configuration are found on the burner and in the
Installation, Operation and Service Manual. Write the
largest clearance dimensions with permanent ink
according to your model number and configuration in the
open spaces on the tag.
back cover. This copy of the wall tag can be affixed on the
wall near the heater. Know your model number and
installed configuration. Model number and installed
configuration are found on the burner and in the
Installation, Operation and Service Manual. Write the
largest clearance dimensions with permanent ink
according to your model number and configuration in the
open spaces on the tag.
2.2 Corrosive Chemicals
Roberts-Gordon LLC cannot be responsible for ensuring
that all appropriate safety measures are undertaken prior
to installation; this is entirely the responsibility of the
installer. It is essential that the contractor, the sub-
contractor, or the owner identifies the presence of
combustible materials, corrosive chemicals or
halogenated hydrocarbons* anywhere in the premises.
that all appropriate safety measures are undertaken prior
to installation; this is entirely the responsibility of the
installer. It is essential that the contractor, the sub-
contractor, or the owner identifies the presence of
combustible materials, corrosive chemicals or
halogenated hydrocarbons* anywhere in the premises.
* Halogenated Hydrocarbons are a family of chemical
compounds characterized by the presence of halogen
elements (fluorine, chlorine, bromine, etc.). These com-
pounds are frequently used in refrigerants, cleaning
agents, solvents, etc. If these compounds enter the air
supply of the burner, the lifespan of the heater compo-
nents will be greatly reduced. An outside air supply must
be provided to the burners whenever the presence of
these compounds is suspected. Warranty will be invalid
if the heater is exposed to halogenated hydrocarbons.
compounds characterized by the presence of halogen
elements (fluorine, chlorine, bromine, etc.). These com-
pounds are frequently used in refrigerants, cleaning
agents, solvents, etc. If these compounds enter the air
supply of the burner, the lifespan of the heater compo-
nents will be greatly reduced. An outside air supply must
be provided to the burners whenever the presence of
these compounds is suspected. Warranty will be invalid
if the heater is exposed to halogenated hydrocarbons.
2.3 National Standards and Applicable Codes
All appliances must be installed in accordance with the
latest revision of the applicable standards and national
codes. This refers also to the electric, gas and venting
installation. Note: Additional standards for installations in
Public Garages, Aircraft Hangars, etc. may be applicable.
latest revision of the applicable standards and national
codes. This refers also to the electric, gas and venting
installation. Note: Additional standards for installations in
Public Garages, Aircraft Hangars, etc. may be applicable.
The heater must not be operated in environmental
temperatures below 0° C.
temperatures below 0° C.
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.
in product damage.