Sony 530P Manual Do Utilizador
Ch
apt
apt
er 9
Se
tt
ing
Up
the Camc
Up
the Camc
or
der
156
9-5 Audio Input System
For the operation of the WRR-855A/855B, refer to the
manual supplied with the WRR-855A/855B.
manual supplied with the WRR-855A/855B.
Notes
• When the XLR connection automatic detection function
is on, even if the AUDIO IN CH-1 or CH-2 switch is set
to WIRELESS, the signal input to the AUDIO IN CH1
or CH2 connector is automatically selected when an
audio cable is connected to the AUDIO IN CH1 or CH2
connector. In such a case, set REAR XLR AUTO to OFF
on the AUDIO-1 page of the MAINTENANCE menu.
to WIRELESS, the signal input to the AUDIO IN CH1
or CH2 connector is automatically selected when an
audio cable is connected to the AUDIO IN CH1 or CH2
connector. In such a case, set REAR XLR AUTO to OFF
on the AUDIO-1 page of the MAINTENANCE menu.
• The audio signals to be recorded on audio channels 3 and
4 depend on the settings of the AUDIO IN CH-3/CH-4
switches without being affected by the XLR connection
automatic detection function.
switches without being affected by the XLR connection
automatic detection function.
Fitting the WRR-862 (Using a BP-GL65/
GL95/L60S/M100 Battery Pack)
GL95/L60S/M100 Battery Pack)
1
(1) Attach the WRR tuner fitting (not supplied,
service part number: A-8278-057-A) to the back
of the camcorder.
of the camcorder.
1
Use a Phillips type screwdriver to tighten the
four screws placed in the tuner fitting. For
three of these screws, insert the screwdriver
through the corresponding hole and tighten the
screw.
four screws placed in the tuner fitting. For
three of these screws, insert the screwdriver
through the corresponding hole and tighten the
screw.
2
Loosen the adjustment screws.
3
Adjust the tuner fitting position for a BP-
GL65/GL95/L60S/M100 Battery Pack to be
attached, and tighten the adjustment screws to
fix its position.
GL65/GL95/L60S/M100 Battery Pack to be
attached, and tighten the adjustment screws to
fix its position.
4
Attach the mount plate supplied with the
WRR-862.
WRR-862.
(2) Attach the battery pack.
For details about attaching the BP-GL65/GL95/L60S/
M100 Battery Pack, see 9-1-1 “Using a Battery Pack”
on page 147.
M100 Battery Pack, see 9-1-1 “Using a Battery Pack”
on page 147.
2
Mount the tuner on the WRR tuner fitting.
3
Connect the tuner power cord to the DC OUT
connector of the camcorder, and the audio output cable
to the AUDIO IN CH1 or CH2 connector.
connector of the camcorder, and the audio output cable
to the AUDIO IN CH1 or CH2 connector.
4
Set the switches as follows.
• Set the LINE / AES/EBU / MIC switch for the
channel to which the audio out cable is attached to
MIC.
MIC.
• When the XLR connection automatic detection
function is off, set the AUDIO IN CH-1 or CH-2
switch for the channel to which the audio output
cable is connected to REAR.
If the XLR connection automatic detection function
is on, the input signal for audio recording is selected
automatically, and therefore this setting is not
required.
switch for the channel to which the audio output
cable is connected to REAR.
If the XLR connection automatic detection function
is on, the input signal for audio recording is selected
automatically, and therefore this setting is not
required.
WRR-855A/
855B
855B
to WIRELESS for the channel to be used.
Back of
camcorder
camcorder
BP-GL65/GL95/L60S/
M100
M100
Adjustment screws
Phillips type screwdriver
Mount plate
(supplied with WRR-862)
(supplied with WRR-862)
WRR-862