ONKYO DV-SP501 Manual Do Utilizador
23
Connecting the Power/Turning on the DV-SP501
Before connecting
• The DV-SP501 is shipped with the POWER switch in
the on position (
ON). When the power cord is
plugged in for the first time, the DV-SP501 will auto-
matically enter the standby state and the STANDBY
indicator will light (same condition after step 2
below).
matically enter the standby state and the STANDBY
indicator will light (same condition after step 2
below).
are complete (the connection to a TV is required).
Note:
• This player features a screen saver and an auto power
off function. If the player is stopped and no button is
pressed for five minutes, the screen saver starts. If the
disc tray is closed but no disc is playing and no control
is pressed for 30 minutes, the player automatically
goes into standby.
pressed for five minutes, the screen saver starts. If the
disc tray is closed but no disc is playing and no control
is pressed for 30 minutes, the player automatically
goes into standby.
1
Plug the supplied power cord
into the AC INLET and then into
the power outlet on the wall.
into the AC INLET and then into
the power outlet on the wall.
• Do not use a power cord other than
the one supplied with the DV-SP501.
The power cord supplied is designed
for use with the DV-SP501 and
should not be used with any other
device.
The power cord supplied is designed
for use with the DV-SP501 and
should not be used with any other
device.
• Never have the power cord discon-
nected from the DV-SP501 while the
other end is plugged into the wall
outlet. Doing so may cause an elec-
tric shock. Always connect by plug-
ging into the wall outlet last and
disconnect by unplugging from the
wall outlet first.
other end is plugged into the wall
outlet. Doing so may cause an elec-
tric shock. Always connect by plug-
ging into the wall outlet last and
disconnect by unplugging from the
wall outlet first.
2
Press POWER to switch on the
main power.
main power.
The DVD Player enters standby mode.
The STANDBY indicator lights up.
• The buttons on the remote controller
The STANDBY indicator lights up.
• The buttons on the remote controller
do not operate if the POWER switch
is set to OFF.
is set to OFF.
• To switch off the main power, press
POWER again.
RETURN
SETUP
TOP MENU
MENU
CU
RSOR
PU
SH TO ENTE
R
ANDBY
ST
OFF
ON
STANDBY/ON
POWER
DISPLAY
PLAY MODE
DIMMER
CLEAR
STOP
PLAY
PAUSE
STANDBY/ON
POWER
AC INLET
To a wall outlet
OFF
ON
POWER
3
Press STANDBY/ON on the DVD
Player or ON on the remote con-
troller.
Player or ON on the remote con-
troller.
The DVD Player turns on and the
STANDBY indicator turns off.
• To put the DVD Player in the standby
STANDBY indicator turns off.
• To put the DVD Player in the standby
mode, press STANDBY/ON on the
DVD Player, or STANDBY on the
remote controller. Be sure to set the
volume to minimum before putting
the DVD Player in the standby mode
for the next use to avoid sudden loud
sound reproduction.
DVD Player, or STANDBY on the
remote controller. Be sure to set the
volume to minimum before putting
the DVD Player in the standby mode
for the next use to avoid sudden loud
sound reproduction.
• While the STANDBY indicator
lights up, the DVD Player can
receive signals from the remote con-
troller. However, if you press
POWER on the DVD Player to
switch off the main power, the
remote controller cannot be used to
turn on the DVD Player.
receive signals from the remote con-
troller. However, if you press
POWER on the DVD Player to
switch off the main power, the
remote controller cannot be used to
turn on the DVD Player.
• Setting the STANDBY button to
standby does not shut off the power
completely.
completely.
ANDBY
ST
STANDBY/ON
DV-SP501_En.book Page 23 Tuesday, May 20, 2003 4:17 PM