Toshiba 53AX61 Manual Do Utilizador
Intr
oduction
Connecting
y
our
T
V
Using
the
Remote
Contr
ol
Setting
up
y
our
T
V
Using
the
T
V
’s
F
eatur
es
Appendix
Index
25
53AX61(E)
Adjusting the color convergence
This projection TV uses three separate TV tubes: red, green, and blue.
The red, green, and blue images are projected onto the screen where
they converge to form a full-color picture. You can see a clear picture
only when the three images converge correctly. Convergence may drift
over time or if you move the TV. (If the image on your screen is clear,
skip this procedure.)
The red, green, and blue images are projected onto the screen where
they converge to form a full-color picture. You can see a clear picture
only when the three images converge correctly. Convergence may drift
over time or if you move the TV. (If the image on your screen is clear,
skip this procedure.)
To adjust the color convergence:
Note: The TV must be on for at least 30 minutes before adjusting the
color convergence.
color convergence.
1. Press MENU, and then press
x or • until the PICTURE menu
appears.
2. Press
y or z to highlight CONVERGENCE (below left).
3. Press
x or • to display the center CONVERGENCE menu
(below right). If you see separate red, blue, or green crossed lines,
you should adjust the convergence.
you should adjust the convergence.
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
P CTURE ANTENNA
I
MODE
SPORTS
PREFERENCE
FLESH TONE
ON
OFF
COOL
NO I
REDUCTION
SE
CONVERGENCE
SAVE NEW
SAVE NEW
COLOR
TEMPERATURE
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3
EX I T
TO SELECT POS I
I ON
T
:
ENTER
RED
B L U E
TO SELECT COLOR
:
4. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting. If both red and blue need adjusting, you
must perform steps 4 and 5 twice.
must perform steps 4 and 5 twice.
5. Press
y (up), z (down), x (left), or • (right) on the remote
control to converge the red or blue line into the green line. When
correctly adjusted, you will see two single crossed white lines.
correctly adjusted, you will see two single crossed white lines.
6. Press EXIT to display the circumference CONVERGENCE
menu.
7. Press the corresponding Number button (1–4 and 6–9) to select
the area you want to adjust (below left).
8. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting (below right). If both red and blue need
adjusting, you must perform steps 8 and 9 twice.
adjusting, you must perform steps 8 and 9 twice.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
PUSH
1
8
2
9
3
6
7
1
4
9
–
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3
RED
B L U E
EX I T
TO SELECT POS I
I ON
T
:
ENTER TO SELECT COLOR
:
9. Press
yzx • to converge the red or blue line into the green line,
until you see two single crossed white lines.
10. To select another area to adjust, press EXIT once, and then repeat
steps 7 through 9.
11. To close the CONVERGENCE menu, press EXIT twice.
EXIT
yzx •
Number
MENU/
ENTER
ENTER