Toshiba 30HF85 Manual Do Utilizador
17
Appendix
Using the TV
’s
Features
Setting up
your TV
Using the
Remote Control
Connecting
your TV
W
elcome to
elcome to
T
oshiba
Important
Safeguards
Programming the remote control to operate
your other devices
your other devices
This remote control is pre-programmed to operate Toshiba satellite
receivers, VCRs and DVD players. To control cable TV converters/
satellite receivers, VCRs and DVD players other than Toshiba models,
you must follow the steps below to program your remote control.
1.
receivers, VCRs and DVD players. To control cable TV converters/
satellite receivers, VCRs and DVD players other than Toshiba models,
you must follow the steps below to program your remote control.
1.
Refer to the code tables (on pages 18 and 19) to find the
corresponding code for your brand.
If more than one code is listed, try each one separately until you
find the one that works.
corresponding code for your brand.
If more than one code is listed, try each one separately until you
find the one that works.
2.
If you are programming the remote control to operate your:
• Cable TV converter/satellite receiver: Press “CBL/SAT.”
• VCR: Press “VCR.”
• DVD player: Press “DVD.”
• Cable TV converter/satellite receiver: Press “CBL/SAT.”
• VCR: Press “VCR.”
• DVD player: Press “DVD.”
3.
While holding down RECALL, press the Channel Number buttons
to enter the three-digit code for your cable TV converter/satellite
receiver, VCR or DVD player brand.
to enter the three-digit code for your cable TV converter/satellite
receiver, VCR or DVD player brand.
4.
Point the remote control at the cable TV converter/satellite
receiver, VCR or DVD player, and press POWER to test the code.
• If the cable TV converter/satellite receiver, VCR or DVD player
receiver, VCR or DVD player, and press POWER to test the code.
• If the cable TV converter/satellite receiver, VCR or DVD player
responds, you entered the correct code.
• If the cable TV converter/satellite receiver, VCR or DVD player
does not respond, repeat steps 1–4 using another code.
5.
Press “TV” to control the TV.
For future reference, write down the codes you used:
Cable TV converter/satellite receiver code _____________________
VCR code ______________________________________________
DVD player code _________________________________________
Notes:
• When shipped from the factory, the remote
control is set to operate your TV.
• If you do not enter the code within 10
seconds from step 1 or if you enter a code
not listed below, this operation is canceled.
not listed below, this operation is canceled.
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does
not respond to any of the codes for your
VCR, set the switch to the other position
(VCR1 or VCR2) and reprogram the remote
control.
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does
not respond to any of the codes for your
VCR, set the switch to the other position
(VCR1 or VCR2) and reprogram the remote
control.
Recall
Channel
Numbers
Numbers
Program the remote
control to recognize the
brand of your DVD
player (see
“Programming the
remote control to
operate your other
devices” below.) The
buttons shown at right
will then control the
DVD player.
Press “DVD” first.
control to recognize the
brand of your DVD
player (see
“Programming the
remote control to
operate your other
devices” below.) The
buttons shown at right
will then control the
DVD player.
Press “DVD” first.
Power
Number
buttons
DVD Skip/Search
/
DVD
Recall
TOP Menu
ENTER
DVD MENU
Pic Size (TV)
Mute (TV)
Input (TV)
Volume +/-
(TV)
DVD controls
To control a DVD player:
▲▼
▼
▼
Using the
Remote Control
DVD Clear
TV
VCR
DVD
CBL/SAT
J3S40121A(E)_P16-23
18/01/2005, 9:49 AM
17