Toshiba W43 Manual Do Utilizador
17
Engl
ish
SETTING UP YOUR TV
When Encryption is WEP, Key ID setting is
available. Press
available. Press
B
/
b
to select Key ID and press
c
and
B
/
b
to select 1 (default), 2, 3 or 4.
Press
B
/
b
to highlight Done and press OK.
When the message “Wireless configuration is
complete.” appears on screen, press OK.
complete.” appears on screen, press OK.
NOTE:
Settings are not saved if BACK is pressed
before Done is selected.
m
The Advanced Network Setup screen will
appear.
appear.
When the DHCP function of the router connected
with this TV is On, you can set Auto Setup to On
or Off. (This should usually be set to On.)
When the DHCP function of the router is Off, set
Auto Setup
with this TV is On, you can set Auto Setup to On
or Off. (This should usually be set to On.)
When the DHCP function of the router is Off, set
Auto Setup
to Off, and set the IP Address DNS
address(es) manually.
You can view the fixed MAC address for the TV, if
one is installed.
one is installed.
Press
B
/
b
to highlight Next.
n
Press OK, and Network Connection Test will start.
A message will appear to indicate if the connection
was successful or if could not be completed.
was successful or if could not be completed.
NOTE:
The result of Network Connection Test
does not always guarantee the connection.
To cancel the Network Connection Test:
Press BACK while testing.
Press BACK while testing.
When the network can be accessed, Software
Upgrade
Upgrade
starts automatically. When Software
Upgrade
is completed, proceed to the next step.
o
Press OK, and TV Power On Control screen will
appear. Select Disabled or Enabled and highlight
Next
appear. Select Disabled or Enabled and highlight
Next
.
p
Press OK, and Companion Device screen will
appear. Select On or Off from Enable Control and
Media Renderer
appear. Select On or Off from Enable Control and
Media Renderer
and highlight Next.
q
Press OK. If the Ant/Cable/Satellite screen
appears, press
appears, press
B
/
b
to select Antenna, Cable or
Satellite
, and then press OK to check (
).
If DVB-C is not supported in your area, Cable will
not be displayed.
not be displayed.
• When you select Antenna or Cable, follow step
18 to 21.
• When you select Satellite, skip to step 22.
• When you select Antenna (or Cable) and
• When you select Antenna (or Cable) and
Satellite
, the Satellite Settings startup screen
will appear automatically after completing the
Antenna
Antenna
(or Cable) scan and pressing OK.
r
Press
BbC c
to highlight Next and press OK.
The Auto Tuning start up screen will appear with
the option to select between DTV and ATV, DTV
or ATV if available. Press
the option to select between DTV and ATV, DTV
or ATV if available. Press
c
and
B
/
b
to select
the appropriate mode and press OK.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
xxx xxx xx x
xxx xxx xx x
xxx xxx xx x
xxx xxx xx x
xxx xxx xx x
Quick Setup
Country
Location
Network
Smart TV
Channel Tuning
Advanced Network Setup
3/5
Previous
Next
Auto Setup
IP Address
Subnet Mask
Default Gateway
Auto Setup
Primary DNS Address
Secondary DNS Address
On
On
OK
5/5
Network Connection Test
Network connection was completed successfully.
Quick Setup
Country
Location
Network
Smart TV
Channel Tuning
TV Power On Control
1/2
We recommend you Enable TV Power On
Control for quick access to Toshiba
services. Once enabled you will be able to
view Internet and Menu systems faster.
This mode will result in your TV using
higher power consumption than when
Disabled.
Previous
Next
Disabled
Enabled
TV Power On Control
Disabled
Antenna
Cable
Satellite
Previous
Next