Fostex D2424 Manual Do Utilizador
Model D2424 Reference Manual (Names and Functions)
18
Rear panel section
7. Optional Panel
The additional installation panel for the optional
Model 8345 (TC/SYNC card x1) or Model 8350 (AES/
EBU card x 1). Normally, it can be used with the
panel remained installed.
Model 8345 (TC/SYNC card x1) or Model 8350 (AES/
EBU card x 1). Normally, it can be used with the
panel remained installed.
<Note>
Installation of the option must be done by our Fostex
Service Station. For details, please inquire at your nearest
Fostex Service Station.
Service Station. For details, please inquire at your nearest
Fostex Service Station.
1. Analog Input jack
(connector: PHONE)
External analog audio signals to the D2424 are input
here. These are connected, for example, to external
mixer's group out (BUSS OUT) connectors. As signals
applied to [INPUT 1-8] are simultaneously sent to
tracks 1-8, 9-16 and 17-24, tracks for recording must
be selected via the [RECORD TRACK] select key.
here. These are connected, for example, to external
mixer's group out (BUSS OUT) connectors. As signals
applied to [INPUT 1-8] are simultaneously sent to
tracks 1-8, 9-16 and 17-24, tracks for recording must
be selected via the [RECORD TRACK] select key.
6. AC IN connector
The power cable packaged with this recorder is
connected here.
connected here.
5. REMOTE THRU connector
RS-422 control signal (SONY 9PIN PROTOCOL or
Fostex System Exclusive Message) input from the
[REMOTE INPUT] connector is output here.
This is connected to the second recorder REMOTE
INPUT when controlling a multiple number of
recorders.
Fostex System Exclusive Message) input from the
[REMOTE INPUT] connector is output here.
This is connected to the second recorder REMOTE
INPUT when controlling a multiple number of
recorders.
4. REMOTE INPUT terminating switch
This REMOTE INPUT terminating switch (100
Ω
) is
switched ON for normal use of an inputted RS-422
control signal into the [REMOTE INPUT] connector.
When controlling a multiple number of recorders,
the last one only is switched ON; the others are
switched OFF.
control signal into the [REMOTE INPUT] connector.
When controlling a multiple number of recorders,
the last one only is switched ON; the others are
switched OFF.
3. REMOTE INPUT connector
External RS-422 control signal (SONY 9PIN
PROTOCOL or Fostex System Exclusive Message) is
input here to control this recorder.
PROTOCOL or Fostex System Exclusive Message) is
input here to control this recorder.
<Note>
Always plug the power cable to the recorder before
plugging the cable into the wall outlet.
plugging the cable into the wall outlet.
8. SCSI connector [SCSI]
(connector: half-pitch 50-pin)
Connect a backup SCSI device to SAVE/LOAD data.
Up to one SCSI devices can be connected to the SCSI
connector.
Up to one SCSI devices can be connected to the SCSI
connector.
* Refer to page “
91
” for more details on SAVE/LOAD
using a SCSI device.
<Note>
Analog input/output can be switched for balance/
unbalance via the SETUP mode. At initial setup, it is set
for unbalance.
unbalance via the SETUP mode. At initial setup, it is set
for unbalance.
• For functions at installation of the optional Model
8345, please refer to [References] on the last page of
this manual.
8345, please refer to [References] on the last page of
this manual.
2. Analog Output jack
(connector: PHONE)
Analog audio signals (Channels 1-24) from D2424
are output here. For example, this is connected to
the external mixer [TAPE IN] connector.
are output here. For example, this is connected to
the external mixer [TAPE IN] connector.
<Note>
When using a current drive formatted to 96kHz 24 bits
or 88.2kHz 24 bits, only [OUTPUT 1-8] will be functional.
or 88.2kHz 24 bits, only [OUTPUT 1-8] will be functional.
75
Ω
WORD
OUTPUT
INPUT
OUTPUT
DATA
16 - 9
24 - 17
8 - 1
100
Ω
RS422
THRU
AC-IN
INPUT
16 - 9
24 - 17
8 - 1
SCSI
ON OFF
REMOTE
MIDI
INPUT
THRU
OUTPUT
1
2
3
4
5
6
7
8
1
2
3
4
13
14
15
16
5
6
7
8
17
18
19
20
9
10
11
12
21
22
23
24
NE PAS OUVRIR
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
SHOCK, DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
ANALOG INPUT BALANCE [ +4dBu ] / UNBALANCE [ -10dBv ]
ANALOG OUTPUT BALANCE [ +4dBu ] / UNBALANCE [ -10dBv ]
ON OFF
DATA
MIDI
WORD
SCSI
REMOTE
ANALOG OUTPUT BALANCE [ +4dBu ] / UNBALANCE [ -10dBV ]
ANALOG INPUT BALANCE [ +4dBu ] / UNBALANCE [ -10dBV ]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
7