Sony MAV-555SS Manual Do Utilizador

Chap

ter
 5

B

a

s

ic

 F

u

n

c

tion
s

 of
 Eac

h

 Mod

e

5-4 (E)

5-4 Basic Operations with DTR+Panel and DTR+DTR Modes

Assuming it is okay to delete all material on this unit, 
execute ALL ERASE (menu 099) on the basic menu, 
and reboot the unit.

* If you don’t want to delete all material, change this unit 

to the Panel mode, delete the “LIVE1” (and “LIVE2”) 
material, the change back to the DTR+Panel (or 
DTR+DTR) mode.

For basic menu operations, please see Section 3-4-2, “Basic Menu 
Operation” (page 3-23).

After changing the recording time (LIVE DURATION), 
the materials must be deleted per Step 2 above. It is not 
possible to extend the recording time and continue 
recording from previously recorded material, or to 
otherwise change the recording time in the midst of 
recording.

For precautions and setup related to LIVE DURATION, please see 
Section 3-4-1, “Basic Menu Settings” (page 3-18).

During loop recording, when the recording time exceeds 
the time set for LIVE DURATION, the oldest recorded 
material is overwritten, so that even when the length of the 
recording exceeds preset recording time, the most recent 
recorded images are always stored up to the time set for 
LIVE DURATION.

Loop recording is performed by the following procedure:

Set the LIVE DURATION (menu 034) on the basic 
menu for DTR-1 (and DTR-2) to the desired time.

Set DTR-1 LOOP REC (or DTR-2 LOOP REC) on.

Assuming it is okay to delete all material on this unit, 
execute ALL ERASE (menu 099) on the basic menu, 
and reboot the unit.

* If you don’t want to delete all material, change this unit 

to the Panel mode, delete the “LIVE1” (and “LIVE2”) 
material, the change back to the DTR+Panel (or 
DTR+DTR) mode.

For basic menu operations, please see Section 3-4-2, “Basic Menu 
Operation” (page 3-23).  

Once material has been recorded, loop recording cannot be 
turned on or off until the recorded material is erased.

After the initial settings described in the previous section, 
the following operations can be performed.

In SS mode, when setting the preroll time, it is necessary 
to specify a value three times larger than that of the desired 
time.
Examples
• When you want to specify 10 frames (525)

Input [1S 00F] and the preroll time becomes 10 frames.

• When you want to specify 3 seconds

Input [9S 00F] and the preroll time becomes three 
seconds.

While holding the SHIFT key, press the REC key on 
the DTR-3000.
Recording starts at the recording port of this unit that 
is connected to the operating DTR-3000.

To stop recording, hold the SHIFT key and press the 
STOP key on the DTR-3000.
To resume recording, hold the SHIFT key while 
pressing the REC key again.

Recording cannot be restarted randomly within previously 
recorded material: it is always resumed from the point 
where it was last stopped. To re-record from the beginning 
of the recording area, perform the following procedure:

Assuming it is okay to delete all material on this unit, 
execute ALL ERASE (menu 099) on the basic menu, 
and reboot the unit.
* If you don’t want to delete all material, change this 

unit to the Panel mode, delete the “LIVE1” (and 
“LIVE2”) material, the change back to the 
DTR+Panel (or DTR+DTR) mode. However, if you 
want to retain previously recorded material, rename 
it to something other than “LIVE1” or “LIVE2.”

Follow the above steps for recording from the DTR-
3000 to re-record.
Recording starts at the beginning of the recording 
area.

Press the PLAY key on the DTR-3000.
• Playback starts at the playback port of this unit that 

is connected to the controlling DTR-3000.