Sony HES-V1000 Manual Do Utilizador
127
Other Remote Uses
Programming AV components to the
device selection buttons
device selection buttons
You can use the remote with Sony and other branded AV
components. To use with other AV components, set the
component’s manufacturer code to the corresponding device
button on the remote (TV, VCR, CUSTOM buttons, etc.).
Codes that can be entered vary depending on the device selection
button (page 127).
components. To use with other AV components, set the
component’s manufacturer code to the corresponding device
button on the remote (TV, VCR, CUSTOM buttons, etc.).
Codes that can be entered vary depending on the device selection
button (page 127).
a While holding down RM SETUP, press AV
\/1.
The RM SETUP button flashes.
The RM SETUP button flashes.
b Press the desired device selection button
before the RM SET UP button stops flashing.
Both the RM SETUP button and the device selection
button flash.
Both the RM SETUP button and the device selection
button flash.
c Enter the three-digit manufacturer code
using the number buttons (page 127).
For example, to enter 901, enter “9,” “0,” “1.”
For example, to enter 901, enter “9,” “0,” “1.”
d Press ENTER.
The RM SETUP button flashes twice and turns off.
z
Hints
• To exit the above procedures, press RM SETUP.
• When more than one code is listed, try until you find the one that
• When more than one code is listed, try until you find the one that
works.
• If you cannot finish entering the code, repeat from step 1.
Operating registered devices
a Press the device selection button (TV, AMP,
SAT/CABLE, VCR, or CUSTOM) to change
the remote’s mode.
The button lights up and remains lit for about 30
seconds.
You can operate the device until the device selection
button turns off and the remote returns to the server
mode.
the remote’s mode.
The button lights up and remains lit for about 30
seconds.
You can operate the device until the device selection
button turns off and the remote returns to the server
mode.
Manufacturer code lists
◆Default Settings
The following codes are set to the device selection buttons by
default.
The following codes are set to the device selection buttons by
default.
*1
Only the AV \/1, MUTING, VOL +/– buttons will work.
*2
TV codes (5xx) and AV amplifier codes (9xx) can be assigned to this
button.
button.
*3
The following button functions are added to the AMP button. Refer
also to the instructions supplied with the amplifier.
also to the instructions supplied with the amplifier.
z
Hint
To use the “ON SCREEN” function on a Sony AV amplifier, press
AMP, then press POP UP/MENU.
AMP, then press POP UP/MENU.
◆For AV amplifiers
◆For tuners
◆For CD players
◆For tape/DAT decks
◆For tape decks
SERVER
501 (Sony TV)
*1*2
TV
501 (Sony TV)
AMP
905 (Sony amplifier)
*3
SAT/CABLE
801 (Sony satellite tuner)
VCR
703 (Sony VCR)
CUSTOM
–
Button
Function Name
RED
2CH
GREEN
A.F.D.
BLUE
MOVIE
YELLOW
MUSIC
POP UP/MENU
ON SCREEN
Manufacturer
Code
Sony
905 906 907 908 909
Pioneer
910 913 920 930 932 934 935
Denon
911 916 917 918 923 924
Yamaha
912 919 927 938
JVC
914 915 928 929 931 936
Harman/Kardon
922
Onkyo
921 925 926 933
Manufacturer
Code
Sony
002 005
Manufacturer
Code
Sony
101 102 103
Denon
123 104
JVC
105 106 107
Kenwood
108 109 110
Magnavox
111 116
Marantz
116
Onkyo
112 113 114
Panasonic
115
Philips
116
Pioneer
117
Technics
115 118 119
Yamaha
120 121 122
Manufacturer
Code
Sony
203
Pioneer
219
Manufacturer
Code
Sony
201 202
Denon
204 205
Kenwood
206 207 208 209
Nakamichi
210
Panasonic
216
Philips
211 212
Pioneer
213 214
Technics
215 216
Yamaha
217 218
,continued