Black & Decker CCC3000 Manual De Instruções

Battery storage and carrying caps are provided for use whenever the battery is out of the unit

or charger. Remove cap before placing battery in charger or unit.

Do not store or carry battery so that metal objects can contact exposed 

battery terminals. For example, do not place battery in aprons, pockets, 

boxes, product kit boxes, drawers, etc. with loose nails, screws, keys, etc. 

without battery cap. Without cap in place, battery could short circuit 

causing fire or burns or damage to battery.

1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3.

To  reduce the risk of injury, charge only Black & Decker Power Packs. Other types of 

batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric

shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting

charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to 

damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord

could result in a risk of fire, electric shock or electrocution.
a.  Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed extension

cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If 

the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for 

outdoor use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate

that the cord is suitable for outdoor use.

b.  An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and 

to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater

the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more 

than one extension to make up the total length, be sure each extension contains at least the 

minimum wire size.

Total Extension Cord Length (ft) 

25

50

75 100

125     150

Wire Gauge

18

18

16

16

14        14

9. Use only the supplied charger when charging your unit. The use of any other charger could 

damage the battery or create a hazardous condition.

10. Do not attempt to open the charger or the unit. There are no customer serviceable parts inside. Return

to any authorized Black & Decker service center.

11. DO NOT incinerate battery packs even if they are severely damaged or completely worn out. 
12. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery

cells may occur under extreme usage, charging or temperature conditions. This does not indicate a 

failure. However, if the outer seal is broken and this leakage gets on your skin:
a.  Wash quickly with soap and water.
b.  Neutralize with a mild acid such as lemon juice or vinegar.
c.  If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and 

seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium 

hydroxide.

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any other voltage.

This charger is designed to charge up to 3 batteries at the same time.

Only use anchors supplied with CCC3000 units to properly affix the unit to wall.

•  If not using wall studs:
•  Place metal mounting strip against wall (per fig. 1A).
•  Transfer location of two slotted holes in strip to wall.
•  Drill 1/8" pilot hole per marked location through drywall.
• Using one anchor per slot thread the anchor into wall until flush with surface.
• Align metal mounting strip slots with anchors and install #8 self-tapping screw through mounting strip into

anchor until fully seated.

• Align charger station with holes on mounting strip and using #8 self-tapping screws attach charger station

to strip. Note: all (14) screws are required to attach the station properly.

•  Locate wall studs.
•  Place metal mounting strip against wall (per fig. 1A).
•  Transfer location of two slotted holes in mounting strip to wall studs.
•  Align metal mounting strip slots with wall studs and install #8 wood screw through mounting strip into wall

stud until fully seated.

•  Align charger station with holes on mounting strip and using #8 self-tapping screws attach charger station

to strip. Note: all (14) screws are required to attach the station properly.

1. Plug the charger into an appropriate outlet. 
2. Insert the battery pack into the charger (Fig.1) . Be sure the pack is fully seated in the charger. The red

(charging) light indicates that the charging process has started. 

3. Let the power pack charge initially for 9 hours.  After the initial charge, under normal usage, your power

pack should be fully charged in 3 to 6 hours.

4. Remove the battery pack and place the battery in the tool and be certain that it is inserted fully into

To remove the battery from the product, press down on the release button on the back of the battery  

(Figure 2) and pull out.

The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep

the battery pack fresh and fully charged. 
NOTE:  

A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not been 

kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly 

lose its charge if left in a charger that is not plugged into an appropriate AC source.

1. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the power pack is 

run-down completely, it may take up to 6 hours to become fully charged. Your power pack was sent from

the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours.

2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above +105°F

(+40.5°C). This is important and will prevent serious damage to the power pack. Longest life and best 

performance can be obtained if power pack is charged when air temperature is about 75°F (24°C).

3. While charging, the charger may hum and become warm to touch. This is a normal condition and does

not indicate a problem.

4. If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or

other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when

you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F

(+4.5°C) to 105°F (+40.5°C). (4) If the receptacle and temperature are OK, and you do not get proper

charging, take or send the power pack and charger to your local Black & Decker service center. See Tools

Electric in yellow pages.

Battery Cap

•  Before any use, be sure everyone using this tool reads and understands all safety instructions and other

information contained in this manual. 

• Save these instructions and review frequently prior to use and in instructing others.

When using an electric tool, basic safety precautions should always be 

followed to reduce risk of fire, electric shock, and personal injury, including 

the following.

Some dust created by this product contains chemicals known to the State of 

California to cause cancer, birth defects or other reproductive harm.  Some 

examples of these chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber

To reduce your exposure to these chemicals, wear approved safety 

equipment such as dust masks that are specially designed to filter out

microscopic particles.

This product contains chemicals, including lead, known to the State of 

California to cause cancer, and birth defects or other reproductive harm. 

Wash hands after handling.

with integral batteries or a separate battery pack must be recharged only 

with the specified charger for the battery.  A charger that may be suitable for one type of battery may 

create a risk of fire when used with another battery.

with specifically designated battery pack. Use of any other batteries

may create a risk of fire.

battery in rain

.

in handling batteries in order not to short the battery with conducting  materials such as

rings, bracelets and keys. The battery or conductor may overheat and cause burns.

the batteries.  Released electrolyte is corrosive and may cause damage to the

eyes or skin. It may be toxic if swallowed.

•  Charge battery for 9 hours before attempting to use your tools.

•  The batteries in your power pack are not fully charged at the factory.  Before 

attempting to charge them, thoroughly read all of the safety instructions.

IF YOU SHOULD EXPERIENCE A PROBLEM 

WITH YOUR BLACK & DECKER PRODUCT,

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., 

TYPE No., AND DATE CODE. IN MOST CASES, A

REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR 

COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

............earthing terminal

WALL

WALL