Manual Do Utilizadoríndice analíticoContents9Chapter 1 Hardware Configuration121.1 Introduction121.2 Features131.3 Specifications131.3.1 General131.3.2 Hot-swap Fans141.3.3 Power Supply141.4 Dimensions and Appearance15Figure 1.1: MIC-3043 functional block diagram15Figure 1.2: Appearance of MIC-304315Chapter 2 Installation182.1 Initial Inspection182.2 The MIC-3043 Illustration18Figure 2.1: Front view of MIC-304318Figure 2.2: Front view of MIC-3043192.3 Installation Procedures192.3.1 Card Installation and Removal19Figure 2.3: Installing a card into the chassis202.3.2 Before Operating the System212.3.3 Installing a 3.5" Hard Disk Drive212.3.4 Connecting the rear I/O module222.3.5 Configuring the built-in RAID (SCSI) by RIO module (MIC-3043C series only)22Figure 2.4: SCSI adaptor222.3.6 Configuring the built-in IDE for the RIO module (MIC-3043A and IC-3043B series)23Figure 2.5: IDE adaptor (type B242.3.7 Configuring the built-in SATA for the RIO module (MIC-3043D series)24Figure 2.6: The location of jumper switch24Figure 2.7: Setting table for IDE/SATA selection242.3.8 Replacing the Hot-swap Fan25Figure 2.8: Hot-swappable fan maintenance25Chapter 3 Backplane283.1 General Information283.2 Features283.3 Specification283.4 Slot Assignments29System to peripheral slot signal assignment30Figure 3.1: MIC-3811 and MIC-3812 slot numbering313.5 Connector and Jumper Locations31Backplane connector and jumper description31Figure 3.2: The connector and jumper locations on the front side (MIC- 3811 & MIC-3812)32Figure 3.3: The connector and jumper locations on the rear side. (MIC-3811)32Figure 3.4: The connector and jumper locations on the rear side. (MIC-3812)323.5.1 AC/DC Power Connector (CN3, CN17)333.5.2 Power Switch333.5.3 V I/O Voltage Selection33Figure 3.5: V I/O voltage selection333.5.4 Fan Module Connector343.5.5 Alert indicators34Figure 3.6: Location of alert indicators343.6 Clock Routing Configuration34Appendix A Pin Assignments36A.1 MIC-3812 and MIC-3811 System Slot P1 Connector36MIC-3812 and MIC-3811 system slot P1 connector36A.2 MIC-3812 and MIC-3811 System Slot P2 Connector37MIC-3812 and MIC-3811 System Slot P2 Connector37A.3 MIC-3812 and MIC-3811 System Slots P3 Connector38MIC-3812 and MIC-3811 System Slot P3 Connector38A.4 MIC-3812 and MIC-3811 System Slots P4 Connector39MIC-3812 and MIC-3811 System Slot P4 Connector39A.5 MIC-3812 and MIC-3811 System Slots P5 Connector40MIC-3812 and MIC-3811 System Slot P5 Connector40A.6 MIC-3812 and MIC-3811 Peripheral Slot P1 Connector41MIC-3812 and MIC-3811 Peripheral Slot P1 Connector41A.7 MIC-3812 and MIC-3811 Peripheral Slot P2 Connector42MIC-3812 and MIC-3811 System Slot P2 Connector42A.8 MIC-3812 and MIC-3811 Peripheral Slot P3 Connector43MIC-3812 and MIC-3811 Peripheral System Slot P3 Connector43A.9 MIC-3812 Peripheral Slot P4 Connector44MIC-3812 Peripheral System Slot P4 Connector44A.10 MIC-3811 Peripheral Slot P4 Connector45MIC-3811 Peripheral System Slot P4 Connector45A.11 MIC-3811 Peripheral Slot P5 Connector46MIC-3811 Peripheral Slot P5 Connector46A.12 MIC-3812 Peripheral Slot P5 Connector47MIC-3812 Peripheral Slot P5 Connector47A.13 Fan Module Connectors48Fan Module Connectors48A.14 LED Board Connector48LED Board Connector48A.15 MIC-3812 & MIC-3812 Alarm Board Interface Connector49MIC-3812 & MIC-3812 Alarm Board Interface Connector49A.16 cPCI Power Connector (CN1,CN2, and CN5)50cPCI Power Connector (CN1,CN2, and CN5)50A.17 AC/DC Power Connector (CN3)51AC/DC Power Connector (CN3)51A.18 AC/DC Power Connector (CN17)52AC/DC Power Connector (CN17)52A.19 Enable Power Switch Connector (CN15)52Enable Power Switch Connector (CN15)52A.20 Device Power Connector (CN18)53Device Power Connector (CN18)53Appendix B Ordering Information56Recommended 6U CompactPCI SBC57Tamanho: 900 KBPáginas: 58Language: EnglishAbrir o manual