Manual Do Utilizadoríndice analíticoCHAPTER 1 GENERAL INFORMATION11.1 Introduction21.2 General Specifications31.3 LCD Specifications71.4 Dimensions8Figure 1-1: Dimensions of the PPC-S1238CHAPTER 2 SYSTEM SETUP92.1 A Quick Tour of the Panel PC10Figure 2-1: Front view of the panel PC10Figure 2-2: Rear view of the panel PC11Figure 2-3: Rear and bottom view of the panel PC112.2 Installation Procedures122.2.1 Connecting the power cord122.2.2 Connecting the keyboard or mouse122.2.3 Switching on the power122.3 Running the BIOS Setup Program132.4 Installing System Software142.4.1 Method 1: Use the Ethernet142.4.2 Method 2: Use an FDD142.4.3 Method 3: Use the COM or parallel port142.4.4 Method 4: Use a 3.5" HDD or CD-ROM142.5 Installing the Drivers15INSTALLATION173.1 Overview of Hardware Installation and Upgrading183.2 Installing the 2.5" Hard Disk Drive (HDD)18Figure 3-1: Install the HDD on the HDD carrier19Figure 3-2: Connect HDD to the HDD cable19SDRAM Memory Module20Figure 3-3: Detach the CPU heat sink20Figure 3-4: Place CPU push cover over CPU21Figure 3-5: Insert screw driver into the hole22Figure 3-6: Push CPU in position22Figure 3-7: CPU installation23Figure 3-8: Fan cooling with heatsink assembly installation24Figure 3-9: Installing the memory module253.4.1 Floppy drive installation263.4.2 2nd hard drive or CD-ROM drive installation27Figure 3-10: Install the riser card273.5 Adapter cable installation28Figure 3-11: Install the adapter28CONNECTORS294.1 Jumpers and Connectors304.1.1 Setting jumpers304.1.2 Jumpers and switch31Table 4-1: Jumpers and their functions314.1.3 Locating jumpers and switch32Figure 4-1: Jumpers on the PPC-S123 motherboard324.1.4 Connectors33Table 4-2: Connectors on the PPC-S123 motherboard334.1.5 Locating connectors34Figure 4-2: Locating connectors on the PPC-S123 motherboard344.2 CMOS Clear for External RTC (JP7)354.3 COM-port Interface354.3.1 COM2 RS-232/422/485 setting (JP2, JP3, JP4)35Table 4-3: Clear CMOS / External RTC (JP7)35Table 4-4: COM2 RS-232/422/485 setting (JP2, JP3)35Table 4-5: COM2 RS-232/422/485 setting (JP4)36Table 4-6: Serial port default settings364.3.2 COM3 / COM4 pin 9 output type setting (JP5)374.4 VGA Interface374.4.1 LCD panel power setting37Table 4-7: COM3/COM4 pin 9 setting (JP5)374.5 Watchdog Timer Configuration38Table 4-8: Watchdog activity selection (JP6)38INTERFACE395.1 Introduction405.2 Installation of Ethernet Driver405.2.1 Installation for Windows 98415.2.2 Installation for Windows NT445.2.3 Installation for Windows 2000/ME465.3 Further Information46CHAPTER 6 AGP SVGA SETUP476.1 Introduction486.1.1 Chipset486.1.2 Display memory486.2 Installation of SVGA Driver486.2.1 Installation for Windows 98496.2.2 Installation for Windows NT506.2.3 Installation for Windows 2000536.2.4 Installation for Windows ME546.3 Further Information557.1 Introduction587.2 Installation of Audio Driver587.2.1 Installation for Windows 98597.2.2 Installation for Windows NT617.2.3 Installation for Windows 2000/ME63CHAPTER 8 AWARD BIOS SETUP658.1 Award BIOS Setup668.2 CMOS Setup Utility66Figure 8-1: Setup program initial screen668.3 Standard CMOS Setup67Figure 8-2: CMOS setup screen678.3.1 Hard disk configurations688.4 BIOS Features Setup69Figure 8-3: BIOS features setup screen698.5 Chipset Features Setup73Figure 8-4: Chipset features setup screen738.6 Power Management Setup75Figure 8-5: Power management setup screen758.7 PNP/PCI Configuration Setup77Figure 8-6: PNP/PCI configuration setup screen778.8 Load BIOS Defaults78Figure 8-7: Load BIOS defaults screen788.9 Load Setup Defaults798.10 Integrated Peripherals79Figure 8-8: Integrated peripherals screen798.11 Password Setting808.12 IDE HDD Auto Detection82Figure 8-9: IDE HDD auto detection screen828.13 Save and Exit Setup838.14 Exit Without Saving83Figure 8-10: Save and exit setup screen83CHAPTER 9 TOUCHSCREEN859.1 Introduction869.1.1 General information869.1.2 General specifications869.1.3 Environmental specifications869.2 Installation of Touchscreen Drivers879.2.1 Installation for Windows 98/ME889.2.2 Installation for Windows NT929.2.2 Installation for Windows 200097WATCHDOG TIMER101Programming the Watchdog Timer102PROCEDURES105Figure B-1: Disconnect the IDE connector106Figure B-2: Remove the fuse107Figure B-3: Remove the seven screws on the rear panel107Figure B-4: Separate the front and rear panel108Figure B-5: Remove the inverter and LCD108touchscreen control board109APPENDIX C I/O PIN ASSIGNMENTS111C.1 Keyboard connector (CN8-1)112C.2 Mouse connector (CN8-2)112C.3 COM1 RS-232 serial port (CN1)112Table C-1: Keyboard connector112Table C-2: Mouse connector112Table C-3: COM1 RS-232 serial port112C.4 COM3 RS-232 serial port (CN4)113C.5 COM4 RS-232 serial port (CN5)113Table C-4: COM3 RS-232 serial port113Table C-5: COM4 RS-232 serial port113C.6 COM2 (CN2)114Table C-6: COM2114C.7 Parallel port connector (CN3)115Table C-7: Parallel port connector115Tamanho: 4 MBPáginas: 128Language: EnglishAbrir o manual