Manual Do Utilizadoríndice analíticoAbout This Document7Purpose7Intended audience7Assumptions7Conventions used in this document7Contacting Black Box Technical Support71 Product Overview9ETEP Introduction9ET0010A Physical Description10Front Panel Connectors10Status Indicators11Rear Panel11ET0100A Physical Description12Front Panel Connectors12LED Indicators12Rear Panel13ET1000A Physical Description14Front Panel Connectors14LED Indicators15Rear Panel16ET10000A Physical Description17Front Panel Connectors17LED Indicators17Rear Panel19Features20Specifications21MIB Support242 Installation27Safety Guidelines27Software Requirements27ETEP Site Preparation28Firewall Ports29Installation Instructions: ET0010A29Rack Mount Installation30To install the ETEP in a rack:30Solid Surface Installation32To install the ETEP on a solid surface:32Connecting the Cables: ET0010A34To cable the ET0010A:34Powering On the ET0010A35To power on the ETEP:35Installing the ET0100A36Cabling Requirements: ET0100A36Unpacking the Shipping Carton: ET0100A37Rack-Mount Installation: ET0100A37To install the ETEP in a rack:38Connecting the Cables: ET0100A38To cable the ET0100A:38Powering on the ET0100A39To power on the ET0100A:39Installing the ET1000A40Cabling Requirements: ET1000A41Unpacking the Shipping Carton: ET1000A42Rack Mount Installation: ET1000A42To install the ET1000A in a rack:43Grounding of DC Power Supply: ET1000A44For DC Power Supply Only44For Earth Connection44Connecting the Cables: ET1000A44To cable the ET1000A:44Powering on the ET1000A45To power on the ET1000A:46Installing the ET10000A47Cabling Requirements: ET10000A48Unpacking the Shipping Carton: ET10000A49Rack Mount Installation: ET10000A50To install the ET10000A in a rack:50Connecting the Cables: ET10000A51To cable the ET10000A:51Powering on the ET10000A52Safety Guidelines52Power-Up Procedure53To power on the ET10000A:53Shutting Down the ETEP54To shut down the ETEP from the CLI:543 Initial Setup57Overview57Logging In Through a Serial Link57To log in to the CLI via a serial link:57Configuring the Management Port58About the management port IP address, mask and gateway58About auto-negotiation59To configure the management port:59Setting the Date and Time61To set the date and time:61Entering a Throughput License62To add a license from the command line:62To view the ETEP throughput speed:63Configuration Example63Managing the ETEP634 Maintenance65Preventative Maintenance65What To Do If an Appliance Fails65Obtaining a License for Replacement Units66Replacing a Power Supply66Replacing the ET1000A Power Supply66To replace a power supply in the ET1000A:66Replacing the ET10000A Power Supply67To replace a power supply in the ET10000A:67Tamper Switch and Zeroization69To recover the ETEP following zeroization:70Cable Pinouts70RS-232 Serial Cable: ET0010A and ET10000A70RS-232 Serial Cable: ET0100A, ET1000A Models715 Troubleshooting73Symptoms and Solutions73LED Indicators73Error State74Temperature Threshold and Discarded Traffic74Diagnostic Code Display75Status Codes: ET0010A75Diagnostic Codes: ET0100A, ET1000A and ET10000A76Appendix A Environmental and Regulatory Information77WEEE Directive77RoHS Directive77Regulatory Information77ET0010A Regulatory Information78Safety78Immunity78Emissions78FCC Information (USA)78Interference-Causing Equipment Standard Compliance Notice (Canada)78European Notice79ET0100A Regulatory Information79Safety79Immunity79Emissions79FCC Information (USA)79Interference-Causing Equipment Standard Compliance Notice (Canada)79European Notice80ET0100A Cabling80ET1000A Regulatory Information80Safety80Immunity80Emissions80FCC Information (USA)80Interference-Causing Equipment Standard Compliance Notice (Canada)81European Notice81ET1000A Regulatory Information81Safety81EMI/EMC81FCC Information (USA)81Interference-Causing Equipment Standard Compliance Notice (Canada)82European Notice82ET10000A Regulatory Information82Normas Oficiales Mexicanas (NOM): Electrical Safety Statement82INSTRUCCIONES DE SEGURIDAD82Index85Tamanho: 4 MBPáginas: 88Language: EnglishAbrir o manual