Manual Do Utilizadoríndice analíticoConfiguring the MGX RPM-PR1Accessing the RPM-PR Command Line Interface1Booting the RPM-PR2RPM-PR Bootflash Precautions3Verifying the IOS Files on Bootflash3Verifying the IOS Files on the PXM-45 x: Drive3Initializing the RPM-PR Card4Assigning an IP Address to the Switch Interface4Step 1 Enter show ip int brief to display your router IP interfaces.5Step 2 Enter conf terminal to enter global configuration mode.5Step 3 To enter interface configuration mode for the ATM interface, enter interface switch1 at th...5Step 4 Enter ip address followed by the IP address to be assigned to the ATM switch.5Step 5 Enter end or press Ctrl-Z to exit the configuration interface mode.5Step 6 Enter show ip int brief to display the IP address assigned to the ATM switch. The followin...5Step 7 Enter show run to verify the configuration of the RPM-PR, as shown in the following exampl...5Step 8 Enter copy run start at the prompt to write the configuration to the router NVRAM memory.6Booting RPM-PR Using TFTP from a TFTP Server6Step 1 Enter cc <RPM-PR card slot #> to access the router card.6Step 2 Enter enable and your password, when prompted, so that you can enter privileged commands.6Step 3 Enter config terminal to enter global configuration mode.6Step 4 Enter boot system tftp followed by the address of the server from which you want to downlo...6Step 5 Enter end or press Ctrl-Z to exit configuration mode.6Step 6 Enter show run to view your configuration. The configuration is similar to the one shown h...7Step 7 Enter copy run start at the prompt to write the configuration to the router NVRAM memory.7Step 8 To load the runtime image from the TFTP server, enter the reload command on the RPM-PR.7Configuring Ethernet Interfaces7Preparing to Configure Ethernet Interfaces7Back Card Bay and Interface Port Numbers8Configuring IP Addresses and Starting Ethernet Interfaces8Step 1 At the privileged-level prompt, enter the command global configuration mode as follows:8Step 2 To specify the interface to be configured, enter the following interface subcommand at the...8Step 3 You can assign an IP address and subnet mask to the interface with the ip address configur...9Step 4 Enter any additional configuration subcommands required to enable routing protocols and se...9Step 5 Start up the Ethernet interface by entering the following command:9Step 6 Configure additional interfaces as required.9Step 7 When you have included all of the configuration subcommands to complete the configuration,...9Step 8 Save your configuration changes as follows:9Selecting Half-duplex or Full-duplex Ethernet Communications9Step 1 Enter the full-duplex command to configure full-duplex operation for the FE back cards.9Step 2 Enter the show interfaces fastethernet command to verify that the 2/1 Fast Ethernet interf...9Step 3 Enter the no full-duplex command to return the interface to half-duplex operation.10Step 4 Enter the show interfaces fastethernet command to verify that the 2/1 Fast Ethernet interf...10Step 5 Save your configuration changes.10Selecting the MII Receptacle for Ethernet Communications10Step 1 Enter the media-type mii command to configure the MII receptacle as the media type for the...10Step 2 Enter the show interface command to check your configuration.11Step 3 Save your configuration changes.11Selecting Media Type 100 for Fast Ethernet Communications11Step 1 Enter the media-type 100 command.11Step 2 Enter the show interface command to check the configuration.11Step 3 Save your configuration changes.12Verifying the Configuration12Using the show Commands to Verify the New Interface Status12Step 1 Enter the show interface <back card type> <bay/port> command to specify one of the new int...12Step 2 Enter the show protocols command to display the protocols configured for the entire system...13Step 3 Enter the show running-config command to display the running configuration file.13Step 4 Enter the show startup-config command to display the configuration stored in NVRAM.13Viewing the Hardware Configuration13Viewing the Boot Variable14Using show Commands to Display Back Card Information14Verifying Ethernet Connectivity15Establishing 1:N Redundancy Between Two or More RPM-PR Cards16Step 1 Logon to the switch.16Step 2 If you have not done so already, initialize both cards as described earlier in this chapte...16Step 3 Enter the dspcds command to verify that the primary and secondary RPM-PR card are in the “...16Step 4 Enter the addred command.16Step 5 When the reset is complete, enter the dspcds command to show the primary and secondary car...17Step 6 To display the redundancy relationship between all cards in the switch, enter the dspred c...17Step 7 Return to the primary RPM by entering the cc command, cc <redPrimarySlotNum>.17Step 8 Enter copy run start to save the configuration to the PXM-45 hard disk E:RPM directory.17Using Softswitch to Change the Active Card18Step 1 Enter the softswitch command.18Step 2 Enter the same command to switch the active card back to the original RPM-PR.18Deleting Redundancy18Adding Additional Primary Cards19Upgrading Redundant RPM-PR Cards19Step 1 On the primary active RPM-PR card, modify the running configuration to boot from the new u...19Step 2 Enter WR MEM to execute the write memory command, which saves the configuration.19Step 3 Enter the softswitch command, as follows, to switch to the secondary card.19Step 4 Modify the configuration of the secondary card to boot from the new upgrade software and e...19Step 5 Enter the softswitch command, as follows, to switch to the primary card from secondary car...19Step 6 Continue this procedure from Step 2 for all remaining cards.20Upgrading Non-redundant RPM-PR Cards20Step 1 Configure the RPM-PR card to store its configuration on the PXM hard disk by entering the ...20Step 2 Modify the running configuration to boot from the new upgrade software by entering the boo...20Step 3 Enter WR MEM to save the configuration.20Step 4 Reset the RPM-PR card by entering the reset command from the PXM or the reload command fro...20Tamanho: 200 KBPáginas: 20Language: EnglishAbrir o manual
