Manual Do Utilizadoríndice analíticoContents3Getting Started7Introduction7Audience7Nomenclature7Related Publications8List of Features8How to Get Help11Web Access11Email Access11Telephone Access11Warranty Coverage11Product Introduction13Overview13AR120213AR1202 Front Panel13AR1202 Back Panel13LEDs14AR120415AR1204 Front Panel15AR1204 Back Panel15LEDs16Installation19Site Preparation19Environment19Power Requirements20Network Connection20Cables Required20Tools Required20Unpacking and Inspecting21Wall-Mounting Option22Rack-Mounting Option22Installing the AR1202 and AR1204 Router23Table Top Installation23Network Connections26Connecting the WAN Cable26Connecting Drop and Insert Cables27Operator Interface27Configuration29Logging In29Command Tips29Ethernet Configuration Tip30Changing Login Parameters30Default Configuration32Configuring Drop and Insert Multiplexing34Configure the drop_insert interface34Configure the mode type34Display interface drop_insert Foundry35Configure the link35Display interface drop_inserts35Display interface drop_insert Foundry36Switching Routing/IPMUX Modes36Switching to Routing Mode36Switching to IPMux Mode36Boot Process36Upgrading System Software36Before Downloading the AR01_#### File37Upgrading Software37Booting From a Network TFTP Server38Router# file download 192.168.10.1 tftpdir/8.0/AR01_####38Copyright (c)38Copyright (c)38CPU: Foundry38Variation: 8.3.238RSP Version 1.1/238Creation date Sep 8, 2000, 19:14:2438Press any key to stop auto-boot....38[Foundry Boot. reboot in 1 minute if CR not pressed]:38[Foundry Boot]:38[Foundry Boot]:38.38.38.38[Foundry Boot]:38[Foundry Boot]: c38‘_’= clear field; ‘=’ = go to previous field; ^D = quit38boot device : f10 InPci038processor number ) 038[Foundry Boot]: P40boot device : InPci40unit number : 040processor number : 040host name : host40file name : tftpdir/8.0/T2000.Z40host 1net [h] : 10.11.12.1340gateway 1net [g] : 111.2.3.25440user [u] : wind40ftp password [pw] : ****040flags [f] : 0x8a40target name [tn] : T120040ether [e] : InPci40Specifications41System Specifications41WAN Interfaces43LAN Interfaces44Cable Pinouts45MIBs47Troubleshooting51Alarms and System Status51WAN Statistics51Network Tests52Ping Test52Other Tests52Diagnostics Tips532 Make sure the power supply is working properly.533 Verify that the DC power cord is functional.532 Make sure the terminal is powered up.532 If you are using a non-Foundry LAN cable, refer to Table A.8 on pageA-6 to check the cable pin...533 Make sure both the router and the adjacent LAN nodes are powered on.532 Make sure cables are properly connected between the service provider’s switch, hub, or LAN and ...533 If you are using a non-Foundry LAN cable, refer to Table A.8 on pageA-6 to check the cable pin...534 Verify that the LAN is properly configured at the command line. Also, check IP addresses, subne...535 Use the display arp command for target addresses.536 If excessive collisions exist on the LAN, switch to a less congested LAN segment.532 If the cable is good, perform a BERT test on the link.543 If the BERT test passes, check the WAN link between the two ends with external test equipment. ...542 If CRC-6 errors or BPVs are present, check the Line Build Out (LBO) configuration settings at b...542 If a QRW test is in progress, check for the same link configuration at the far end.542 Flash is corrupt.552 Configure the modem for 9600/8/None, and no flow control.553 Power cycle the Foundry router continuously by pressing the Enter key until you see the followi...55[Foundry Boot]554 Type c, and press Enter.555 The following prompts will be displayed. Type the bolded entries and press Enter.55boot device: lnPci (Lower case “L”, not “1”.)55processor number: 055host name: host55file name: “The path and file name on your tftp server (e.g., tftpboot/NCM.Z)”55inet on ethernet (e): x.x.x.x:ffffff00 (This is the system’s Ethernet address:netmask.)55inet on backplane (b): Not needed.55host inet (h): x.x.x.x (The ip address of the tftp server.)55gateway inet (g): x.x.x.x (Your router’s address- not necessary in the same subnet.)55user (u): wind (This is a required field.)55ftp password (pw) (blank = use rsh): wind (This is a required field.)55flags (f): 0x8a55target (tn): Foundry55startup script (s): Not needed.55other (o): lnPci (This is a lowercase “L”, not a “1”.)556 At this point, you will be at the Foundry prompt [Foundry Boot]. Type @ and press Enter. This w...557 Once the system is booted and you have logged in, you must format the Flash by issuing the foll...55file format NCM558 When the format is complete, follow the upgrade procedures to finish the process.55Tamanho: 1000 KBPáginas: 56Language: EnglishAbrir o manual