Manual Do Utilizadoríndice analíticoTable of Contents31 Before You Start 191.1 Symbols Used 191.2 Safety Information 2101.2.1 Warnings 2101.2.2 Cautions 4121.3 Customer Service Information 6142 Introduction 7153 Specifications and Environmental Conditions 9163.1 Specifications 9163.2 Environmental Conditions 9163.3 Hardware Warranty and Assistance 10173.3.1 Instrument Warranty 10173.3.2 In-Warranty Repairs 10173.3.3 After-Warranty Repairs 10173.3.4 Equipment Maintenance Agreements 11183.3.5 Customer Support 11183.3.6 Customer Support Agreement 11183.3.7 Customer Site Assistance 11184 Quick Start 13194.1 Unpacking 13194.2 Set-up 13194.3 Power 14204.4 Setting the Temperature 14205 Installation 17225.1 Bath Environment 17225.2 “Dry-out” Period 17225.3 Bath Preparation and Filling 17225.3.1 Drain Valve Installation Instructions 17225.3.2 Filling With Fluid 18235.4 Power 19246 Bath Use 21256.1 General 21256.2 Comparison Calibration 21256.3 Calibration of Multiple Probes 22267 Parts and Controls 23277.1 Control Panel 23277.2 Bath Tank and Lid 24287.3 Back Panel 24288 General Operation 27308.1 Bath Fluid 27308.1.1 Temperature Range 27308.1.2 Viscosity 27308.1.3 Specific Heat 27308.1.4 Thermal Conductivity 28318.1.5 Thermal Expansion 28318.1.6 Electrical Resistivity 28318.1.7 Fluid Lifetime 28318.1.8 Safety 28318.1.9 Cost 29328.1.10 Commonly Used Fluids 29328.1.10.1 Water (Distilled) 29328.1.10.2 Ethanol 29328.1.10.3 Mineral Oil 30338.1.10.4 Silicone Oil (Dow Corning 200.05, 200.10, 200.20) 30338.1.10.5 Halocarbon 0.8 30338.1.11 Fluid Characteristics Table 30338.1.11.1 Limitations and Disclaimer 31348.2 Stirring 32358.3 Power 32358.4 Heater 32358.5 Refrigeration 32358.5.1 Operation 33368.5.2 Important Refrigerant Information 33368.6 Temperature Controller 33369 Controller Operation 35389.1 Bath Temperature 35389.2 Temperature Set-point 35389.2.1 Programmable Set-points 35389.2.2 Set-point Value 37409.2.3 Temperature Scale Units 37409.3 Scan 38419.3.1 Scan Control 38419.3.2 Scan Rate 38419.4 Secondary Menu 39429.5 Heater Power 39429.6 Proportional Band 39429.7 Cutout 41449.8 Controller Configuration 42459.9 Operating Parameters 42459.9.1 High Limit 42459.9.2 Low Limit 42459.9.3 Cooling 43469.10 Serial Interface Parameters 43469.10.1 Baud Rate 44479.10.2 Sample Period 44479.10.3 Duplex Mode 44479.10.4 Linefeed 45489.11 Calibration Parameters 45489.11.1 Hard Cutout 46499.11.2 R0 46499.11.3 ALPHA 46499.11.4 DELTA 46499.11.5 BETA 464910 Digital Communication Interface 475010.1 Serial Communications 475010.1.1 Wiring 485110.1.2 Setup 485110.1.2.1 Baud Rate 485110.1.2.2 Sample Period 495210.1.2.3 Duplex Mode 495210.1.2.4 Linefeed 495210.1.3 Serial Operation 495210.2 Interface Commands 495211 Calibration Procedure 535511.1 Calibration Procedure 535511.1.1 Calibration Equipment 535511.1.2 Calibration 535512 Maintenance 555713 Trouble Shooting 575913.1 Troubleshooting 575913.2 CE Comments 586013.2.1 EMC Directive 586013.2.2 Low Voltage Directive (Safety) 586013.3 Wiring Diagram 5961Figures7Figure 1 Drain Valve Installation—IMPORTANT: Do Not Over Tighten. Follow the installation instructions above. 1823Figure 2 CTR-80 Control Panel 2327Figure 3 Back Panel 2529Figure 4 Controller Operation Flowchart 3639Figure 5 Serial Cable Wiring 4851Figure 6 Wiring Diagram 5961Tables8Table 1 International Electrical Symbols 19Table 2 Table of Various Bath Fluids 3134Table 3 Controller Communications Commands 5053Table 3 Controller Communications Commands continued 5154Tamanho: 800 KBPáginas: 61Language: EnglishAbrir o manual