Manuais de utilizador para Giant Telecom Limited OL5800B

índice analítico

• OLYMPIA® OL6815

  1
• OWNER’S MANUAL

  1
• 1 Cordless Phone Features

  6
• 2 Caller ID Features

  6
• 3 Set Up

  6
• 4 Olympia OL6815 – Quick Programming Guide

  7
• 5 Installation and Charging of the Battery Pack

  8
• 6 Layout of Keys and Indicators

  10
• 7 Power Up

  11
  • 1. After the battery pack is installed in the Handset and the Base Unit is powered up, the Handset should be placed in the cradle of the Base Unit for charging and setting a new security code (registration).

    11
  • 2. Once the second Handset has been charged, remove the first Handset from the Base cradle, and then place the second Handset in the Base to allow registration to take place. This should take less than one minute.

    11
  • 3. The completion of a successful security code transfer operation will be indicated by a flash of the ‘In Use’ LED on the Base Unit and a beep generated by Handset.

    11
  • 4. In the event you do not receive the visual and audible indicators, check to ensure the Base is powered and the battery pack is connected. Return the Handset to the Base cradle.

    11
  • 5. In Standby mode, the handset number will be displayed.

    11
  • 8 Answering Calls on Either Handset

    11
    • 1. The incoming call is signaled by a ringing sound from the Handset and by the blinking of the Base Unit’s ‘In Use/Charge’ LED. The Handset’s ‘New Call’ LED also blinks during ringing.

      11
    • 2. When the Handset is in the cradle, simply pick it up to talk. It will automatically answer the call. The ‘TALK’ button will be disabled for 5 seconds. This is the Auto Answer feature.

      11
    • 3. When the Handset is away from the Base Unit, press the ‘TALK’ button on the Handset. You can also press any number key 0-9, * or # to answer the call. This is the Any Key Answer feature. The ‘In Use / Charge’ LED turns on after the connection is successful.

      11
    • 4. If the communication link cannot be established within 8 seconds, three error beeps will be heard from the Handset to indicate communication has failed.

      11
  • 9 Make a Call from Either Handset

    11
    • 1. Each new call must begin by pressing the ‘TALK’ button on the Handset. It will scan for a clear channel of communication. At the same time, ‘TALK’ will be shown on LCD display.

      11
    • 2. If the communication link is not established within 8 seconds, there error beeps will be heard from the Handset to indicate communication has failed.

      11
    • 3. You can dial the phone number first, then press TALK (this is called pre-dial); or press TALK first, then dial.

      11
  • 10 Terminate a Call

    11
    • 1. To terminate a call, press the ‘TALK’ button; -OR-

      11
    • 2. Place the Handset in the cradle; the call is then terminated.

      11
  • 11 Short Paging (To Locate the Handsets)

    11
    • 1. Press the ‘PAGE’ key on the base unit. ‘PAGING’ will be shown on the LCD display and the Handset will emit 3 short beeps, followed by a 1-second pause, then 3 short beeps.

      11
  • 12 Long Paging

    12
    • 1. Press and hold down the ‘PAGE’ key on the Base Unit. ‘PAGING’ will be shown on the LCD display and your Handset will beep. If you hold the button for 5 seconds, the page will be extended to 60 seconds.

      12
    • 2. Press any key on the Handset to stop paging.

      12
  • 13 Selecting System Language

    12
    • 1. There are 2 ways to access ‘SET LANGUAGE’ mode: 1) ‘SET LANGUAGE’ will appear on the LCD when your phone is charged for the first time or powered up after it has been without power for an extended period; -OR- 2) During idle (on hook) mode, press and hold ‘MEM.’ until ‘SET LANGUAGE’ appears.

      12
    • 2. Setup mode begins with language selection. Your phone offers 3 languages - English, French, and Spanish. Press ‘▼/#’ or ‘▲/*’ to choose the desired language and then press the ‘MEM.’ key to confirm. After confirmation, ‘Area Code ?’ will be displayed.

      12
  • 14 Setting Local Area Code

    12
    • 1. If you dial 7 digits to make a local call, you need enter your 3-digit area code. The digits will shift to the left one by one as you enter them. If you dial 10 digits to make a local call, enter ‘000’ (if it is not already programmed for ‘000’).

      12
    • 2. Press ‘MEM.’ key to confirm. After confirmation, ‘SET T/P ? is displayed.

      12
  • 15 Setting Tone/Pulse (Preset to Tone)

    12
    • 1. The current setting (T or P) is displayed.

      12
    • 2. Press ‘▼/#’ or ‘▲/*’ to select the desired setting, and the display will update the current setting: ‘SET T/P? T’( ‘SET T/P? P’( ‘SET T/P? T’……..

      12
    • 3. Press ‘MEM.’ to confirm. After confirmation, you will enter ‘RINGER’ setting.

      13
  • 16 Setting RINGER ON/OFF

    13
    • 1. The current RINGER ON/OFF setting is displayed.

      13
    • 2. Press ‘▼/#’ or ‘▲/*’ to select the desired setting, and the display will update to the current setting: ‘RINGER ON’( ‘RINGER OFF’( ‘RINGER ON’……..

      13
    • 3. Press ‘MEM.’ key to confirm. After confirmation, you will enter HANDSET NUMBER setting.

      13
    • If you don’t want to reset the time and date, press ‘MEM’ again to exit programming mode and return the Handset to idle mode.

      13
  • 17 Setting Handset Number

    13
    • 1. Press 1 - 4, or ‘▼/#’ or ‘▲/*’ to select a handset number. Each handset requires a unique number. We recommend using ‘1’ and ‘2’.

      13
    • 2. Press ‘MEM.’ key to confirm. After confirmation, you will enter DATE / TIME setting.

      13
  • 18 Setting Date & Time

    13
    • 1. Press the appropriate digits to enter first the time and then the date.

      13
    • 2. To change the AM/PM setting, press any digit (0-9).

      13
    • 3. Press ‘▼/#’ or ‘▲/*’ to skip forward or backward.

      13
    • 4. Press ‘MEM’ key to confirm. After confirmation, you will enter CONTRAST setting.

      13
  • 19 Setting Display Contrast

    14
    • 1. Press ‘▼/#’ or ‘▲/*’ to set the desired contrast.

      14
    • 2. Press ‘MEM.’ key to confirm. After confirmation, the display returns to standby.

      14
  • 20 Caller ID Operation

    14
    • 1. RECEIVING CALLS

      15
      • a. When Caller ID is activated, the Telephone Company sends the caller’s telephone number (and name, if available) and the call’s date and time between the first and second rings. The device receives and displays this information for each call and updates the display with the current date and time. The NEW CALL indicator will flash. Once you review all new CID records, the NEW CALL indicator turns off.

        15
      • b. The display also indicates if caller information is not available or intentionally blocked by the sender:

        15
      • c. After 20 seconds, the display returns to standby mode, showing ‘NEW CALL XX where XX is the number of new calls. NEW CALL LED blinks until you review all new CID / Call Waiting ID records.

        15
    • 2. REVIEWING NEW CALLS

      15
      • a. In standby mode, with the ‘NEW CALL’ indicator flashing, pressing ‘▲/*’ or ‘▼/#’, the LCD displays the latest new call information.

        15
      • b. Repeatedly press ‘▲/*’ or ‘▼/#’ to review all new call information in the order of receipt until the LCD displays ‘END NEW CALL’ and the ‘NEW CALL’ indicator stops blinking.

        16
      • c. If the received call information is the same as any of the existing new calls, the ‘RPT’ icon will be on to indicate REPEAT CALL. The most recently arrived CID will be saved attached with a new date / time stamp. The older record will be deleted. After you review this call, the ‘RPT’ icon will turn off.

        16
      • d. If you do not review other calls for 20 seconds, the time and date will be displayed, and the call counter will show the total number of new calls including those already reviewed.

        16
    • 3. REVIEWING OLD CALLS

      16
      • a. In standby mode, press ‘▲/*’ or ‘▼/#’ to review old call information from the oldest to the newest (‘*’ button) or from the newest to oldest (‘#’ button).

        16
      • b. When the end of the list is reached, ‘END’ is displayed.

        16
      • c. If there are no records in memory, ‘NO CALLS’ is displayed.

        17
    • 4. DELETE INDIVIDUAL CALL

      17
      • a. When you review Caller ID information, you can delete it from memory. Press ‘▼/#’ or ‘▲/*’ until you see the call record you want to delete.

        17
      • b. Press ‘DELETE’; the LCD displays ‘ERASE ?’.

        17
      • c. Press ‘DELETE’ again to confirm deletion.

        17
      • d. If the deleted message was the last record in memory, the display will go back to standby mode. If there are other records in memory, the next CID record received after the deleted record will be displayed.

        17
      • e. VIP call records can’t be deleted. See Set VIP Calls for details.

        17
    • 5. DELETE ALL CALLS

      17
      • a. If the new call information has been reviewed, you can erase all call records. If there are any new calls in call list, ‘ERASE ALL’ will not work.

        17
      • b. In the standby (idle) mode, press and hold ‘DELETE’ until the LCD displays ‘ERASE ALL?’.

        17
      • c. Press ‘DELETE’ again to confirm deletion, and return to standby mode.

        17
    • 6. SET VIP CALLS (assigning VIP designations to CID records)

      18
      • a. Press ‘▼/#’ or ‘▲/*’ to select the call which you want to designate ‘VIP’.

        18
      • b. Press and hold ‘CALLS’ for 2 seconds; the VIP icon turns on.

        18
      • c. To remove the VIP designation, press and hold ‘CALLS’ for 2 seconds.

        18
    • 7. ‘Smart’ Dialing from Caller ID

      18
      • a. In idle mode, press ‘#’ or ‘*’ to select the CID record you want to dial.

        18
      • b. If the display phone number is in the correct format, press ‘TALK’ to dial.

        18
        • 1. If the display shows 10 digits in the second line, such as ‘123-456-7890’.

          18
        • 2. If the display shows 7 digits in the second line such as ‘456-7890’, & the area code is set as ‘123’:

          18
      • c. With the correct number displayed, press ‘TALK’. The display will show ‘TALK’.

        18
      • d. After a 2-second delay, the unit will enter TALK mode automatically. The dialed digits appear from right to left on the display.

        18
    • 8. Save CID to Speed Dial memory

      19
      • a. In idle mode, press ‘▼/#’ or ‘▲/*’ to select the Caller ID number that you want to save.

        19
      • b. Press ‘CALLS’ to select the number format that you want to save.

        19
      • c. Press ‘MEM.’ The screen will display ‘LOCATION ? X’, where X is a digit (0-9). Note: only the phone number can be saved to speed dial memory.

        19
      • d. ‘X’ is the lowest empty memory slot. Press ‘MEM.’ to confirm. If you prefer a different memory location, press the desired location number (0-9). The display will now show ‘MEM X STORED’. WARNING: Make sure you’re not unintentionally replacing a number already stored in that location!

        19
  • 21 Visual Message Notification

    19
    • After receiving a ‘new message’ signal from your service provider, the envelope icon will appear, alerting you that you have new message(s).

      19
    • After reviewing all new messages, the icon will disappear.

      19
  • 22 Speed Dial Memory (0…9)

    20
    • 1. Memory Programming **NOTE: Each handset has its own speed dial memory**

      20
      • a. With the Handset in the idle (on hook) mode, enter the desired phone number. (NOTE: to insert a 4-second Pause in the dialing sequence, press REDIAL.)

        20
      • b. Press ‘MEM’. You will see ‘LOCATION? X’. ‘X’ is the lowest empty memory location.

        20
      • c. Press ‘MEM’ to confirm, or press a different location (0-9), if desired. Programming is completed! CAUTION: Make sure you’re not replacing an important phone number already in that location!

        20
    • 2. Memory editor

      20
      • a. Enter memory search mode by pressing ‘MEM.’. Press ‘▼/#’ or ‘▲/*’ to select the memory location you want to edit.

        20
      • b. You can add additional digits to the existing number. As you enter numbers, the display will shift entered digits from right to left, to a maximum of 16 digits. If you try to enter more than 16 digits, an error tone will be generated.

        20
      • c. If you make a mistake, press ‘DELETE’ to delete the last digit entered. The display will shift entered digits from left to right-hand side.

        21
      • d. Press ‘FLASH’ to clear all entered digits (including any pre-existing digits).

        21
      • e. Press ‘MEM.’ to save the entered number. The display will show ‘LOCATION? X’, where X is a digit (0-9)

        21
      • f. Press ‘MEM.’ to confirm saving number to the displayed location; OR press a digit (0-9) to save the number to another memory location. The display will show ‘MEM X STORED’ for 6 seconds.

        21
    • 3. Delete individual speed dial location

      21
      • a. Enter memory search by pressing ‘MEM.’. Press ‘▼/#’ or ‘▲/*’ to select the entry you want to delete.

        21
      • b. Press ‘DELETE’ to delete the entry. The display will show ‘ERASE ?’.

        21
      • c. Press ‘DELETE’ to confirm deletion, or press any key to cancel.

        21
    • 4. Speed Dialing with Handset OFF

      21
      • a. Enter memory search by pressing ‘MEM.’. Press ‘▼/#’ or ‘▲/*’ to select the number you want to dial.

        21
      • b. Press ‘TALK’ . The unit will enter TALK mode automatically. The number will scroll across the screen from right to left as it is dialed.

        21
    • 5. Speed Dialing with Handset ON

      21
      • a. Press ‘TALK’ to turn the phone On. The display will show ‘TALK 0:00’.

        21
      • b. First, press ‘MEM.’. Second, press the desired memory location. The phone number will scroll across the screen from right to left as it is dialed. If memory is empty, an error tone will be generated. You’ll need to repeat this step in order to speed dial.

        21
  • 23 Pre-dialing (Handset OFF)

    22
    • 1. You can enter a phone number while in the standby mode. The maximum number of digits is 24. For example, enter number 0:

      22
    • 2. Press ‘DELETE’ to delete last entered digit. If all digits are deleted, the Handset will return to standby.

      22
    • 3. Press ‘FLASH’ to clear all entered digits and return to standby mode.

      22
    • 4. Press ‘TALK’. The unit will enter TALK mode automatically. The phone number will scroll across the screen from right to left as it is dialed.

      22
    • 5. Saving a number in Speed Dial memory From the idle mode, enter the phone number (up to 16 digits), and then press ‘MEM.’. The display will show ‘LOCATION ? X’. Press ‘MEM.’ to confirm; OR, press a digit key to select a different memory location. The display shows ‘MEM X STORED’.

      22
  • 24 Redial with Handset OFF

    22
    • 1. Press ‘REDIAL’ while in standby mode. The display will show the redial number. If the number is greater than 24 digits, the display will show only the last 24 digits.

      22
    • 2. Use the keypad to add additional digits to the redial number.

      22
    • 3. Press ‘DELETE’ to delete last entered digit. If all digits are deleted, it will return to standby.

      22
    • 4. Press ‘FLASH’ to clear all entered digits and return to standby.

      23
    • 5. Press ‘TALK’. The unit will enter TALK mode automatically. The number will scroll across the screen from right to left as it is dialed.

      23
    • 6. You can also press ‘TALK’, then press ‘REDIAL’ to dial the contents of Redial.

      23
    • 7. Saving the contents of REDIAL to Speed Dial memory In idle mode, press ‘REDIAL’, then press ‘MEM.’. The display will show ‘LOCATION ? X’. Press ‘MEM.’ to confirm, OR, press a digit key to select a different memory location. The display shows ‘MEM X STORED’.

      23
  • 25 Dialing Digits

    23
  • 26 Call Timer

    24
    • 1. The call timer comes up automatically when you are in TALK mode, on the 3rd line of the display. After 10 seconds, the call timer will appear as dialing activities are completed.

      24
    • 2. The call timer counts up to 999 minutes and 59 seconds. After that, the timer will show ‘0:00’

      24
    • 3. When handset goes idle (on hook), the call timer will remain on the display for 5 seconds.

      24
  • 27 Battery/Voltage Low Detection

    24
    • 1. Battery detection is engaged at all times, except while the Handset is charging.

      24
    • 2. If a low battery condition is detected, then the Handset will enter into ‘Battery Low’ condition, and will beep at 10-second intervals. Your Handset will change to ‘Halt’ mode immediately and continue to beep. If the Handset is in TALK mode, it will change to ‘Halt’ mode immediately and continue to beep after the call ends. The display will show ‘BATTERY LOW’.

      24
    • 3. Once the battery is recharged, the Handset will return to normal operation.

      24
  • 28 Mute

    24
  • 29 Changing Volume

    24
  • 30 Transferring a Call from One Handset to the Other

    25
    • 1. In talk mode, press and hold FLASH until TRANSFER is displayed.

      25
    • 2. Press the number of the destination handset ( 1 – 4 ).

      25
    • 3. Press FLASH to confirm. After confirmation, the sending handset will return to standby, and the destination handset will ring.

      25
    • 4. Answer the call by pressing any key on the destination handset.

      25
    • 5. If there is no answer from the destination handset within 20 seconds, the sending handset will ring. If it does not answer within 20 seconds, the call will be dropped and the phone will return to standby mode.

      25
  • 1 Setup

    26
  • 2 Recording a Memo

    28
    • 1. Press REC/MEMO. You will be prompted to select a Mailbox.

      28
    • 2. Select the desired MAILBOX. You will hear 'Now Recording', followed by a beep.

      28
    • 3. Speak towards the Base Unit. Press STOP when finished. Your memo is stored like a message from an outside caller.

      28
  • 3 Listening to Your Messages

    28
  • 4 Deleting Messages

    29
  • 5 Remote Operation

    29
  • 6 Other Important Things You Should Know

    29
  • 7 What the Message Window is saying

    30