Manual Do Utilizadoríndice analíticoAbout This Guide4Table of Contents51. Product Features7HP LCD Monitors7• Large diagonal display7• Maximum graphics resolution: 1366 x 768 @ 60Hz (18.5 in.) 1600 x 900 @ 60Hz (20 in.) 1920 x 1080 @ 60Hz (23 in.)7• VGA analog signal7• DVI digital signal on select models7• Easy viewing from a sitting or standing position, or while moving from one side of the monitor to the other7• Tilt adjustment7• Removable base7• Built in stereo speakers on select models7• Security lock slot for a locking security cable (security cable sold separately)7• Plug and Play capability, if supported by your computer system7• On-Screen Display (OSD) adjustments in several languages for easy setup and screen optimization7• Power Saver to reduce energy consumption7• HDCP (High Bandwidth Digital Content Protection) on DVI input for select models7• Software and utilities CD, containing the following: Drivers Documents72. Safety and Maintenance Guidelines8Important Safety Information8• Do not disable the power cord grounding feature. The grounding plug is an important safety feature.8• Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.8• Disconnect power from the product by unplugging the power cord from the electrical outlet.8Safety Precautions8• Use only a power source and connection compatible with this monitor, as indicated on the label/back plate of the monitor.8• Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the power cord does not exceed the rating of the power c...8• Install your monitor near a power outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.8• Do not allow anything to rest on the power cord. Do not walk on the cord.9Maintenance Guidelines9• Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If the monitor is not operating properly or has been dropped or damaged, contact an authorized...9• Use only a power source and connection appropriate for this monitor, as indicated on the label/back plate of the monitor.9• Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the cord does not exceed the rating of the cord. Look on...9• Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.9• Turn the monitor off when not in use. You can substantially increase the life expectancy of the monitor by using a screen saver program and turning off the monitor when not in use9• Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objec ts of any kind into cabinet slots or other openings.9• Do not drop the monitor or place it on an unstable surface.9• Do not allow anything to rest on the power cord. Do not walk on the cord.9• Keep the monitor in a well-ventilated area, away from excessive light, heat or moisture.9• When removing the monitor base, you must lay the monitor face down on a soft area to prevent it from getting scratched, defaced, or broken.9Cleaning the Monitor91. Turn off the monitor and the computer.92. Unplug the monitor from the wall outlet or the power brick.93. Clean the monitor plastics with a clean cloth dampened with water.94. Clean the monitor screen with an antistatic screen cleaner.93. Setting Up the Monitor10Unpacking the Monitor101. Unpack the monitor. Make sure all contents are included. Store the packing box.102. Turn off the computer and other attached devices.103. Prepare a flat area to assemble the monitor. You may need a flat, soft, protected area for placing the monitor screen-down while preparing it for installation.10Installing the Monitor10Preparing the monitor for desktop use101. Set the monitor screen face down on a flat, soft, protected table or desk surface with the support column overhanging the edge.102. Press the column onto the monitor support column until it locks in place.103. Press the base into the column until it locks in position.114. Lift the monitor to an upright position and place on a flat, stable surface.11Preparing the monitor for wall-mounting111. Check the stability of the wall-mounting fixture.112. Disconnect the power cable and any other cables from the monitor.113. Place the monitor face down on a flat, protected surface.114. Slide the base away from the bottom of the monitor.125. Four threaded holes are exposed. These holes are for screws to attach the swing arm or other mounting fixture to the back of the monitor.126. Follow the instructions included with the mounting fixture to ensure that the monitor is safely attached. The four threaded holes that are on the back of the panel are compliant with the VESA standard for mounting flat-panel monitors.127. Attach a swing arm or other mounting fixture.12Connecting Monitor Cables13Connecting the VGA (Analog) Cable or DVI-D (Digital) Cable131. To connect the VGA cable132. To connect the DVI-D cable (provided with select models)13Connecting the Audio Cable (Select Models)13High-Bandwidth Digital Content Protection (HDCP) (Available on Select Models)14Connecting the Power Cable141. Follow all Electrical and Power Warnings142. Connect one end of the power cable to the monitor and the other end to a grounded electrical outlet.14Adjusting the Tilt151. Face the front of the monitor and hold the base so that you do not topple the monitor while changing the tilt.152. Adjust the tilt by moving the top edge of the monitor either toward or away from you, without touching the screen.154. Operating the Monitor16CD Software and Utilities16Installing Drivers16Installing the monitor driver software from the CD161. Insert the CD in your computer CD drive. The CD menu appears.162. Select the language.163. Click Install Monitor Driver Software.164. Follow the on-screen instructions.165. Ensure that the proper resolutions and refresh rates appear in the Display Control Panel settings.16Downloading updated drivers from the Internet161. Refer to: http://www.hp.com/support .162. Select your country/region.163. Select Download Drivers and Software.164. Enter the model number of your monitor. The software download pages for your monitor are displayed.165. Download and install the driver and software files by following the instructions on the download pages.166. Ensure that your system meets the requirements.16Front-Panel Controls17Using the On-Screen Display (OSD)18• Cancel - to return to the previous menu level.18• Save and Return - to save all changes and return to the OSD Main Menu screen. This Save and Return option is only active if you change a menu item.18Selecting Video Input Connectors22• VGA connector (analog)22• DVI-D connector (digital) (Select Models)22Identifying Monitor Conditions22• Monitor Status - When the monitor is powered on or when the input source signal is changed, a Monitor Status message is displayed for five seconds. The message shows which input is the current active signal, the status of the auto-switch source s...22• Input Signal Out of Range - Change resolution setting to 1366 x 768 @ 60Hz (18.5 in.), 1600 x 900 @ 60Hz (20 in.), 1920 x 1080 @ 60Hz (23 in.).Indicates the monitor does not support the input signal because the resolution and/or refresh rate are ...22• No Source Signal - Indicates the monitor is not receiving a video signal from the PC on the monitor video input connector. Check to determine if the PC or input signal source is off or in the power saving mode.22• Auto Adjustment in Progress - Indicates the auto-adjustment function is active.22• Monitor Going to Sleep - Indicates the screen display is entering a sleep mode.22• Check Video Cable - Indicates the video cable is not properly connected to the computer.22• OSD Lockout - The OSD can be enabled or disabled by pressing and holding the Menu button on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout displays for ten seconds.22• If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.22• If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.22• Power Button Lockout - Indicates the power button is locked. If the power button is locked, the warning message Power Button Lockout displays.22• If the power button is locked, press and hold the power button for 10 seconds to unlock the power button function.22• If the power button is unlocked, press and hold the power button for 10 seconds to lock out the power button function.22• Dynamic Contrast Ratio On - Indicates that Dynamic Contrast Ratio has been turned on. This occurs if Dynamic Contrast Ratio is turned on in the Image Control OSD menu.22• Dynamic Contrast Ratio Off - Indicates that Dynamic Contrast Ratio has been turned off. This occurs if Dynamic Contrast Ratio is turned off in the Image Control OSD menu.22Adjusting Screen Quality231. Allow the monitor to warm up for 30 minutes before adjusting.232. Access the OSD menu, then select Image Control.233. Set the main Clock settings correctly first, because the Phase settings depend on the main Clock settings.When adjusting the Clock and Phase values, if the monitor images become distorted,continue adjusting the values until the distortion disappea...23Power-Saver Feature23Sleep Timer Mode24• Set Current Time24• Set Sleep Time24• Set On Time24• Timer: On/Off24• Sleep Now241. Press the Menu button on the monitor front panel to display the OSD Menu.242. Scroll down and highlight Management.243. Press the OK button to select Management.244. Scroll down and highlight and select Sleep Timer > Set Current Time.24Note: You must set the current local time before you reset the time for Sleep Time or On Time. Note that the time is displayed in a 24-hour clock format. For example, 1:15 p.m. is displayed as 13 hours 15 minutes.245. Press the OK button once to enter the adjustment mode for hours.246. Press the - (Minus) or + (Plus) button to adjust the hour.247. Press the OK button again to enter the time for minutes.248. Press the - (Minus) or + (Plus) button to adjust the minutes.249. Press the OK button to lock in the time chosen.2410. After setting the current time, the highlight automatically skips to Set Sleep Time. Repeat steps 6 through 9 to set Sleep Time.2411. If you do not want to set Sleep Time, press the OK button twice, then select Save and Return to exit the menu.2412. After setting Sleep Time, the highlight automatically skips to Set On Time. Repeat steps 6 through 9 to set On Time.2413. Set the Timer mode to On to activate the Sleep Timer settings.2414. When you are finished, select Save and Return to exit the menu.24A. Troubleshooting25Solving Common Problems25• Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.25• In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer & video card. Check with your computer manufacturer. Also check the monitor's video cable and make sure none of the pins are bent.25• Make sure the HP Monitor Drivers are installed (HP Monitor Drivers are available at : http://www.hp.com/support)25• Adjust the Contrast and Brightness Controls.25• Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back of your computer.25• Move electrical devices that may cause electrical interference as far away from the monitor as possible.25• Use the maximum refresh rate your monitor is capable of at the resolution your are using.25• The Computer Power Switch should be in the ON position.25• The Computer Video Card should be snugly seated in its slot.25• Make sure the monitor's video cable is properly connected to the computer.25• Inspect the monitor's video cable and make sure none of the pins are bent.25• Inspect the monitor's video cable and make sure that none of the pins are bent.25• Make sure the monitor's video cable is properly connected to the computer.25• Adjust Horizontal Position and Vertical Position or press hot- key (OK).25• Adjust RGB color or select color temperature25• Use Windows shut-down mode. Adjust CLOCK and Clock Phase or press the OK button to display ideal setting25Getting Support from hp.com26Preparing to Call Technical Support26• Monitor model number (located on label on back of monitor)26• Monitor serial number (located on label on back of monitor or in the OSD display in the Information menu)26• Purchase date on invoice26• Conditions under which the problem occurred26• Error messages received26• Hardware configuration26• Name and version of hardware and software you are using26Locating the Rating Label26B. Technical Specifications27HP LCD Monitors27DVI-D 24-pin D-type connector (select models)27Preset Video Modes28LCD Monitor Quality and Pixel Policy29C. Agency Regulatory Notices30Federal Communications Commission Notice30Modifications30Cables30Declaration of Conformity for Products Marked with the FCC Logo (United States Only)311. This device may not cause harmful interference.312. This device must accept any interference received, including interference that may cause undesired operation.31European Union Regulatory Notice31• Low Voltage Directive 2006/95/EC31• EMC Directive 2004/108/EC31• Ecodesign Directive 2009/125/EC, where applicable31Canadian Notice32Avis Canadien32German Ergonomics Notice32Japanese Notice32Korean Notice32Power Cord Set Requirements33Japanese Power Cord Requirements33Product Environmental Notices33Energy Star Compliance33Disposal of Waste Equipment by Users in Private Household in the European Union34Chemical Substances34HP Recycling Program34Restriction of Hazardous Substances (RoHS)34Turkey EEE Regulation35Ukraine Restriction of Hazardous Substances35Tamanho: 3 MBPáginas: 35Language: EnglishAbrir o manual
