Manual Do Utilizadoríndice analíticoRC-121OPERATOR’S MANUAL1RHINO®1To the Owner/Operator/Dealer2FLAIL SHREDDER1TABLE OF CONTENTS3SAFETY SECTION 1-13INTRODUCTION SECTION 2-13ASSEMBLY SECTION 3-13OPERATION SECTION 4-13MAINTENANCE SECTION 5-14General Safety Instructions and Practices6Equipment Operation Safety Instructions and Practices9Connecting or Disconnecting Implement Safety Instructions and Practices14Maintenance and Service Safety Instructions and Practices17Concluding Safety Instructions and Practices191 002369 1 DANGER Flail Multi-Hazard202 00725739 1 WARNING Use/Repair Shields & Guards203 999001 1 WARNING Maintain Weight for Steerage204 00725746 1 PELIGRO Spanish - Get Translation205 00756004 3((1)) DANGER Driveline Shield Missing206 00756005 3((1)) DANGER Rotating Driveline207 02967668 1 DANGER Cutting Blades / Thrown Objects208 00756059 1 WARNING Leak Detection, Oil Penetration209 00756494 1 DANGER Driveline Safety2010 00758194 1 WARNING Pitch Point (V-Belt/Pulley)2011 03200347 *1 REFLECT SMV Reflector2012 1458392 {2} REFLECT Red Reflector2013 1458393 {2} REFLECT Yellow Reflector2014 00725747 1 INSTRUCT RC Flail Operating Instructions2015 000678 2(4) INSTRUCT Grease Fitting Inside2016 00725713 1 INSTRUCT Lubrication Chart, RC Flails2117 00725738 1 INSTRUCT Notice to Owner2118 00725715 2 INSTRUCT Pick Up From Lift Points Only2119 00725720 1 INSTRUCT Belt Adjustment2120 00725745 1 INSTRUCT Quick Coupler Hitch Only2121 02964510 1 IMPORTANT Genuine Parts, Flail2122 00773723 1 PELIGRO Rotating Driveline Translation2123 NFS 4 SER PLT Serial Plate2124 D302 2 LOGO RHINO LOGO (4-7/8 x 6-1/2)2125 D303 2 L. NAME RHINO (4-3/8 x 16-1/2)2126 00725626 1 MODEL RC122127 D114 1 WARNING 1000 RPM PTO2128 00763977 1 INSTRUCT Notice to Owner2129 00771283 1 INSTRUCT 5 Year Warranty2130 00775933 1 WARNING Guard Missing2131 D102 1 INSTRUCT PTO-to-Drawbar Adj. Safety Chain2132 00776481 1 INSTRUCT Operators Manual Inside (Decal)2133 00776031 1 ________ Canister, Operators Manual2134 00726339C 1 ________ Operators Manual2135 10058000 3 ________ Bolt2136 00024100 6 ________ Flatwasher2137 02959924 3 ________ Locknut21SAFETY SECTION5Decal Description22Federal Laws and Regulations30ATTENTION OWNER/OPERATOR33OWNER'S RESPONSIBILITIES341. Turn off power to the mower.342. Lower the mower to the ground.343. Set the parking brake.344. Stop the engine and remove the key.341. Use approved fuel container.342. Never smoke while refueling engine.343. Never fill fuel tank indoors. Never remove cap or add fuel to a running or hot engine. Wipe up spilled fuel344. Exhaust fumes are dangerous- open doors if engine is run in garage. Do not run engine indoors.34SAFETY INSTRUCTIONS351. Wire, rope, rags, etc., wound around the shaft.352. Knives missing or broken.353. Knife hanger lugs which have broken off the shaft.354. Cutting rotor bearings worn.355. Cutting rotor bent from striking an object.356. Cutting rotor not rotating at recommended speed.35INTRODUCTION SECTION31SHIPPING STAND REMOVAL38BREATHER PLUG INSTALLATION38TONGUE ASSEMBLY INSTALLATION383-POINT HITCH ASSEMBLY INSTALLATION41ATTACHING AXLE ASSEMBLIES TO MAIN WHEEL BAR TUBE42ATTACHING OPTIONAL HYDRAULIC CYLINDER42ASSEMBLY SECTION37RHINO RC12 FLAIL SHREDDER OPERATION INSTRUCTIONS441. Standard Equipment and Specifications452. OPERATOR REQUIREMENTS46Tractor Requirements and Capabilities472.1 ROPS and SEAT BELT472.2 Tractor Safety Devices472.3 Tractor Horsepower482.4 3-Point Hitch482.5 Drawbar-Pull Type Mower482.6 Front End Weight482.7 Power Take Off (PTO)483. GETTING ON AND OFF THE TRACTOR493.1 Boarding the Tractor493.2 Dismounting the Tractor504. STARTING THE TRACTOR515. CONNECTING THE MOWER TO THE TRACTOR516. SETTING THE MOWER521. Place the tractor and mower on a level surface and completely lower the mower to the ground.532. Shut down the tractor, place the transmission in park, and set the parking brake before dismounting.533. One section at a time, place lifting device (scissors jack or hydraulic jack) under center of cutter housing.534. Remove hex nuts, washers and carriage bolts from bracket at each end of roller. Make certain that roller bracket is free to move once the fasteners are removed. A stuck roller could drop unexpectedly and cause injury.535. Use lifting device to reposition cutter housing to desired cutting height. Align bracket holes with cutter housing, then reinstall hardware.536. Lower cutter housing to the ground and remove lifting device.537. Set cutting height according to procedures above for remaining two cutter sections. Make sure that all three rollers are set at the same height to ensure a even cut across the entire width of the mower.536.1 Leveling Deck547. DRIVELINE ATTACHMENT548. PRE-OPERATION INSPECTION AND SERVICE568.1 Tractor Pre-Operation Inspection/Service578.2 Mower Pre-Operation Inspection/Service579. DRIVING THE TRACTOR AND IMPLEMENT609.1 Starting the Tractor619.2 Brake and Differential Lock Setting629.3 Raising the Mower629.4 Driving the Tractor and Mower639.5 Crossing Ditches and Steep Inclines6410. OPERATING THE TRACTOR AND IMPLEMENT6510.1 Foreign Debris Hazards6710.2 Bystanders/Passersby Precautions6710.3 Engaging the Power Take Off (PTO)6810.4 PTO RPM and Ground Speed6910.5 Operating the Mower6910.6 Shutting Down the Implement7111. DISCONNECTING THE MOWER FROM THE TRACTOR7212. MOWER STORAGE7313. TRANSPORTING THE TRACTOR AND IMPLEMENT7313.1 Transporting on Public Roadways7513.2 Hauling the Tractor and Implement77Problem Possible Cause Remedy78Check for missing knives on Replace missing knives78cutter shaft.78Check to see if knives are Free knives so they swing.78free swinging.78Blade broken or bent. Replace blades.78Cuttershaft bent. Replace cuttershaft.78Drivelines not phased correctly. Replace driveline.78Implement & Tractor yokes must78be in line.78Cuttershaft bearing worn Replace bearings78Improper type lubricant. Replace with proper lubricant.78Excessive trash build-up Remove trash.78around gearbox.78Bearing or gears set up Consult your Dealer.78improperly.78Worn Bearing. Replace bearing.78(Rubbing on pulleys or belt).78Worn Bearing or Gear. Replace Bearing or Gear.78Bent shaft. Replace oil seal and shaft.78Shaft rough in oil seal area. Replace or repair shaft.78Oil seal installed wrong. Replace seal.78Oil seal not sealing in the housing. Replace seal or use a sealant on78OD of Seal.78Oil level too high. Drain oil to proper level.78Sand hole is casting. Replace castings or gearbox.78Gasket damaged. Replace gasket.78Bolts loose. Tighten bolts.78Clutch Slips Excessively Clutch linings badly worn or Repair clutch per maintenance79plates warped. section of manuals.79Too much power for clutch. Reduce ground speed and material79intake.79Oil on facings. Replace facings.79Friction facings glazed. Clean with emery cloth.79Cutting in rocky conditions. Increase cutting height.79Soft “will fit” knives. Use genuine Rhino knives.79Blades dull. Check blades for sharpness.79Grass too wet. Wait for grass to dry.79Grass too long. Mow at 3-1/2” and recut lower.79Travel speed too fast. Use a lower tractor gear.79PTO RPM too low. Mow at engine RPM to match 54079PTO RPM.79Rough, uneven ground. Use a slower speed.79Lower rollers.79Turning Tractor too fast. Slow down when turning.79Mower deck not level. Level the mowing deck.79Blades dull or unbalanced. Sharpen or balance blades.79Deck underside plugged. Clean underside of deck.79Grass too high. Mow at 3-1/2” and recut lower.79Housing plugged. Clean underside of deck.79Spring broke & belt off idler. Replace spring or adjust belt.79Housing plugged. Clean underside of housing.79Debris around pulleys. Remove deck belt shield and clean79out debris.79Grass too high. Mow at 3-1/2” and recut lower.79OPERATION SECTION43MAINTENANCE SECTION81GENERAL MAINTENANCE82LUBRICATION82ROUTINE MAINTENANCE:83CUTTER SHAFT84BLADE REPLACEMENT84BELT ADJUSTMENT AND REPLACEMENT84PULLEY ALIGNMENT AND REMOVAL85CUTTER SHAFT AND BEARING REMOVAL87Cutter Shaft Removal88TOP DRIVE ASSEMBLY SERVICING88DRIVELINE:89STORING THE RC12911. Check the oil level in the Gearbox and lubricate all bearings. See "Lubrication".912. Adjust drive belt tension. See "Belt Drive".913. Inspect for missing and / or broken Blades / Knives. Replace as necessary. See "Knife Replacement".914. Be sure that the Safety Guard is in place and secure.915. Run the Orchard at a low RPM checking to make sure that all driveline parts are moving freely.91Keep children away from danger all day, every day.93Equip tractors with rollover protection (ROPS) and keep all machinery guards in place.93Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.93TO THE OWNER/OPERATOR/DEALER93RHINO92LIMITED WARRANTY921. LIMITED WARRANTIES921.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser921.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.921.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, neglig...921.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.922. REMEDIES AND PROCEDURES.922.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.922.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based.922.03. Purchaser is responsible for returning the goods in question to the Dealer.922.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:92(a) Repair or replace the defective goods or part(s) or92(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer.922.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returni...923. LIMITATION OF LIABILITY.923.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.923.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.923.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTI...923.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.924. MISCELLANEOUS.924.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.924.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.924.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.924.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.92Rhino92An Alamo Group Company921020 S. Sangamon Ave.92Gibson City, IL 6093692800-446-515892Email: parts@servis-rhino.com92Tamanho: 4 MBPáginas: 94Language: EnglishAbrir o manual
