Справочник Пользователя для Marantz SR9200

Use this parameter to specify the distance of each speaker’s position
from the listening position. The delay time is automatically calculated
according to these distances.
Begin by determining the ideal or most commonly used seating
position in the room.
This is important for the timing of the acoustics to create the proper
sound space that the SR9200 and today’s sound systems are able to
produce.
Note that the speakers that you selected “

” or “

” for in the

Speaker Config sub-menu will not appear here.
(There are several usefull books and special DVD and LD’s available
to guide you through proper home theater configuration. If you are
unsure, have your Marantz dealer perform the installation for you.
They are trained professionals familiar with even the most
sophisticated custom installations. Marantz recommends the
WWW.CEDIA.ORG website for further information about this).

To select the each speaker , press 

 or 

 cursor button.

To set the distance for each speaker , press the 

 or 

cursor buttons.

If you finish these setup, move cursor to “

” with 

 or 

cursor button and then press 

 button to go to next page.

Set the distance from the front left speaker to your
normal listening position between 1 and 30 feet in 1.0
foot interval (0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the front right speaker to your
normal listening position between 1 and 30 feet in 1.0
foot interval (0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the center speaker to your normal
listening position between 1 and 30 feet in 1.0 foot
interval
(0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the surround left speaker to your
normal listening position between 1 and 30 feet in 1.0
foot interval (0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the surround right speaker to your
normal listening position between 1 and 30 feet in 1.0
foot interval (0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the subwoofer to your normal
listening position between 1 and 30 feet in 1.0-foot
intervals
(0.3 to 9 meters in 0.3-meter intervals).

Set the distance from a surround back speaker to your
normal listening position between 1 and 30 feet in 1.0-
foot intervals (0.3 to 9 meters in 0.3-meter intervals).

Set the distance from the surround back left speaker to
your normal listening position between 1 and 30 feet in
1.0-foot intervals (0.3 to 9 meters in 0.3-meter
intervals).

Set the distance from the surround back right speaker
to your normal listening position between 1 and 30 feet
in 1.0-foot intervals (0.3 to 9 meters in 0.3-meter
intervals).

• Speakers that you selected "No" or "None" for in the Speaker

Size menu will not appear.

• The setting of Surr.Back L and Surr.Back R appears if set for

two surround back speakers in the Speaker Size menu.

• The setting of Surr.Back appears if set for one surround back

speaker in the Speaker Size menu.

Here you will set the volume for each speaker so that they are all
heard by the listener at the same level.

• The speaker level settings is not available in 7.1channel input

mode and S-Direct mode.

Selects “

” or “

” for generating mode of

test tone Left or Right cursor button.

If you select “

”

, the test tone will be cycled through in a circular

pattern which is Left 

→

Center 

→

Right 

→

Surround Right 

→

Surround

Back Right 

→

Surround Back Left 

→

Surround Left 

→

Subwoofer

→

Left  

→

.. increments of 3 seconds for each channel.

Using the Left and Right cursor buttons, adjust the volume level of the
noise from the speaker so that it is the same level for all speaker.

If you select “

”, adjust the output level of each speaker as

follow.

When you move cursor to FRONT L by pressing 

 cursor

button, the SR9200 will emit a pink noise from the front left
speaker.
At this time, the master volume automatically increases to the
reference level (0dB).
Remember the level of this noise and then press the 

cursor

button.
(Note that this can be adjusted to any level between -10 and +10
dB in 1db intervals.)
The SR9200 will now emit the pink noise from the center speaker.

Using the 

and 

cursor buttons, adjust the volume level

of the noise from the center speaker so that it is the same level as
the front left speaker.

Press the 

cursor button again. The SR9200 will now emit

the pink noise from the front right speaker.

Repeat steps 

 and 

 above for the front right and other speakers

until all speakers are adjusted to the   same volume level.

If you finish these setup, press 

 button, the cursor will move to

“

” and then press 

 button to go to next page.

• Speakers that you selected “No” or “None” for in the Speaker

Size menu will not appear.

• The setting of Surr.Back L and Surr.Back R appears if set for

two surround back speakers in the Speaker Size menu.

• The setting of Surr.Back appears if set for one surround back

speaker in the Speaker Size menu.

• The setup level for each channel is memorized for reproduction

in all surround mode.

• To adjust the speaker levels for 7.1-channel input sources, you

will need to use the 7.1CH-INPUT sub menu. (See page 32).

• In order to correctly set the output levels, use a hand-held Sound

Pressure Level meter (SPL), set to C-Weighting and Slow
averaging.  A Radio Shack

®

 SPL meter (catalogue number 330

- 2055) works well.  Using the internal channel noise
generators, set each channel so that you read 75 dB SPL from
each channel when seated at the listening position.