Справочник Пользователя для Contec RC-U49C-15+

Cable, TV, VIDEO & AUDIO - tune TV to 

Ch 4 

 

 

Cable only (default) 

 
4.  The [CBL] button will blink 3-times and go out, 

storing the selected option. 

 
Programming and using the [TV] SmartKey™ 
 
The [TV] button normally turns on / off your TV.  To 
program the [TV] button to transmit multiple pre-
programmed functions, follow the steps below: 
 
1.  Press [MODE], then [CBL] to select the cable 

mode of your remote. 

 
2.  Press [TV], then [SETTINGS] together until the 

[TV] button illuminates. 

 
3.  Press the option number below for the desired 

functions: 

 

 

 

TV - tune TV to Ch 3 

TV - tune TV to Ch 2 

TV - tune TV to Ch 4 

 

 

TV only (default) 

 
4.  The [TV] button will blink 3-times and go out, 

storing the selected option. 

 
Note:  When using any SmartKey™ to transmit a 
series of functions, be sure to keep your remote 
aimed at the devices to ensure all functions are 
received in their entirety.    

 
 

 

Your model CheckMate

®

 IV remote comes set in its 

“unlocked” operating mode.  While in this mode, it can 
operate all of your cable set-top functions, as well as 
many functions on your TV, VIDEO and AUDIO 
devices. 
 
To lock your remote in its cable operating mode... 
  
1.   Press [CBL], then [MUTE] together until the [CBL]  

button illuminates. 

 
2.  Press [0, 0, 0].  The [CBL] button will blink 3-times  

and go out. 

 
To unlock your remote for multi-device 
operation…

  
1.   Press [CBL], then [MUTE] together until the [CBL] 

button illuminates. 

 
2.   Press [9, 9, 9].  The [CBL] button will blink 3-times  

and go out. 

  

 

 

This button changes the input source of your   
electronic devices.  In the remote's Cable and TV  
modes, this button operates the TV Input function on  
your TV.  In the remote's VIDEO mode, this button  
changes the TV / VCR function on your VCR. 
 
You can program this button so that in the remote's  
cable mode, [TV / VCR] will operate the TV / VCR  
function on your VCR, eliminating the need to change  
modes on the remote. 
 
To program the [TV / VCR] button to operate your 
VCR Input function…  
 
1.  Press [TV / VCR], then [SELECT] together until the 
  [CBL] 

button 

illuminates. 

 

2.  Press [VIDEO].  The [CBL] button will blink 3-times  

and go out. 

 
To return this button to operate the TV Input function 
on your TV, repeat step 1, then press [TV] in step 2. 

 

 
Additional Programming Information 
 
1.  The power / mode buttons will illuminate in  

slow-rotation (i.e. CBL 

Æ TV Æ VIDEO Æ AUDIO 

Æ CBL...)

 while the remote is in a programming 

mode.  In the absence of a keypress entry, the 
power / mode buttons will stop illuminating after 

30 

seconds

 and the remote will exit the programming 

mode. 

 
2.  When programming the remote control using the 

[CH +] or [CH -] buttons (Power function) under 
the Point and Press

®

 Programming method, you 

may find a code that turns a device off but not 
back on.  If this happens… 

 
  

a.  The correct code has not been found as  

 

    you may have a code that operates some  

 

    but not all of the functions of your device.   

 

    Continue pressing [CH +] until your device  

    turn 

on. 

 
        OR 
 
 

b.  You may have gone past the correct matching  

 

    code.   Try pressing [CH -] one press at a time  

 

    until you find a code that turns your device  

    back 

on. 

 
3.  When using the Point and Press

®

 Programming  

method, you can also program your remote using  
buttons other than the [CH +] or [CH -] (as  
described in Section 5) as follows:   

   

a.  [VOL +] – to “go forward” through the codes  

using the “VOL +” function on your devices. 

 
b.  [VOL -] – to “go back” through the codes using  

the “VOL -“ function on your devices.  

 

Note:  When you find the correct code, the 
volume of the device being programmed will 
increase or decrease. 

 
c.   [

S] - to “go forward” through the codes using  

the “CH +” function on your devices. 

 
d. [

T] - to “go back” through the codes using the  

“CH -“ function on your devices. 

 

Note:  When you find the correct code, the  
channel of the device being programmed will  
increase or decrease. 

 

e.   [

XX] - to “go forward” through the codes using  

the “Fast Forward” function on your devices. 

 
f.   [

WW] - to “go back” through the codes using  

the “Rewind” function on your devices.