Справочник Пользователя для Sony M25AE

Chapter 1

Overview

19

Cha

p

ter 1

O

v

e

rv

ie

w

• The LANC jack on the unit has only LANC-S 

functions. The unit has no LANC-M functions. A 
device that is set to LANC-S mode cannot be 
connected to the unit. Either the unit or the other 
device may not operate properly.

• When using the unit as a player, set LANC mode on 

the recorder to M. A VCR that does not have an M/S 
switching function cannot be used to operate the unit. 

• When the device to be connected to the unit has a 

LANC-M function to switch between SHUTTLE A/B, 
select SHUTTLE A for an HDV-formatted tape, and 
SHUTTLE B for a DVCAM/DV (SP)-formatted tape.

• A LANC connection transmits command signals for 

playback, stop, pause playback, as well as the time 
code, tape counter, and data status of the unit.

• Jacks labeled CONTROL L have the same function as 

LANC jacks.

• There are some limitations when you edit an HDV-

formatted tape.

h

Connect this jack to a DSRM-10 remote control unit 
(not supplied) to operate the unit.
You can also use a DSRM-20 (no longer manufactured: 
not supplied).

When you use a CONTROL S device, set 
[COMMANDER] in the [OTHERS] menu to 
[CONTROL S]. 

i

 HDV/DV jack (6-pin)

Use this jack to input/output digital signals that comply 
with the i.LINK standard. Use this jack when a device 
connected to the unit has an i.LINK jack. If you connect 
the unit and another device using the   HDV/DV jack, 
you can minimize deterioration of picture quality during 
recording, dubbing, or capturing still pictures, all by 
means of digital signals processing.

• When you connect a computer and the unit with an 

i.LINK cable, check the direction of the jack. If you 
forcibly insert the jack, the terminal may be damaged 
or cause the unit to malfunction.

•  This jack is only compatible with HDV (1080i)/ 

DVCAM/DV signals. 

For details, see “About i.LINK” on page 99. 

•  If the unit is connected to a device equipped with an 

i.LINK jack, when you intend to disconnect or 
reconnect the i.LINK cable, turn off the device and 
pull out the plug of its power cord from the AC outlet 
beforehand. If you connect or disconnect the i.LINK 
cable while the device is connected to the AC outlet, 
high-voltage current (8 to 40 V) is output from the 
i.LINK jack of the device to the unit. This may cause a 
malfunction.

• Even though the   HDV/DV jack of the unit is a 6-pin 

type, no power is supplied.

• You cannot output EE picture and sound of DVCAM/

DV signals (NTSC, PAL) that are input from the 

HDV/DV jack to the HDMI OUT jack. However,  

HDV signals are output to the HDMI OUT jack.

• When you change the video format setting of [HDMI/

CMPNT] in [VIDEO OUT] of the [IN/OUT REC] 
menu, the video signal output from the S VIDEO OUT 
jack, the VIDEO OUT jack, or the   HDV/DV jack 
may be distorted.

• When you change the video format setting of [HDMI/

CMPNT] and [DOWN CONVERT] of [VIDEO OUT] 
in the [IN/OUT REC] menu, [ALLSCAN MODE] in 
the [DISPLAY SET] menu, or [HDV 

t DV CONV] 

and [DOWN CONVERT] of [i.LINK SET] in the [IN/
OUT REC] menu, the image may be distorted for a 
moment. Also, the above settings may cause 
restrictions on the video output of the unit. 

For details, refer to the table on page 88 and the instructions 
for each menu setting.

• When you change the video format setting of [HDMI/

CMPNT] of [VIDEO OUT] in the [IN/OUT REC] 
menu, the video signals output from S VIDEO OUT 
jack, VIDEO OUT jack, or   HDV/DV jack may be 
distorted.