Справочник Пользователя для Sony HVR-M25AU

Chapter 1

Overview

17

Cha

p

ter 1

O

v

e

rv

ie

w

e

Use these jacks to output component signals.
To connect a device equipped component video input 
connectors, use the COMPONENT OUT jacks on the 
unit. If you use the COMPONENT OUT jacks, you can 
output high-quality video with less signal quality 
deterioration than if you use the S VIDEO jacks.
You can set the output video format by using [HDMI/
CMPNT] of [VIDEO OUT] in the [IN/OUT REC] 
menu.
When the DISPLAY OUTPUT switch is set to ALL, 
text data such as time code, menu, and alarm messages 
are superimposed on a monitor connected using the 
COMPONENT OUT jacks (page 23).

• When images are output in 720p format, some of the 

text image data (outer frame: underscan portion) on the 
monitor may appear cut out. In this case, check the text 
image data on the LCD monitor of the unit or on a 
monitor using the S VIDEO OUT jack or the VIDEO 
OUT jack. Also, when your monitor has an underscan 
function, you can check all the text data on the monitor 
while in underscan mode.

• The setting of [HDMI/CMPNT] of [VIDEO OUT] in 

the [IN/OUT REC] menu is effective for both the 
COMPONENT OUT jack and the HDMI OUT jack 
(page 71).

• When you change the video format setting of [HDMI/

CMPNT] of [VIDEO OUT] in the [IN/OUT REC] 
menu, the video signal output from the S VIDEO OUT 
jack, VIDEO OUT jack, or   HDV/DV jack may be 
distorted for a moment.

• When you play back a tape in DVCAM/DV format and 

while an EE picture in NTSC/PAL is displayed, either 
the 480i resolution or the 576i resolution is output, 
regardless of the setting of [HDMI/CMPNT] of 
[VIDEO OUT] in the [IN/OUT REC] menu. 

• When  [HDMI/CMPNT] of [VIDEO OUT] in the [IN/

OUT REC] menu is set to either [1080i/480i] or 
[1080i/576i], 1080/24p and 1080/30p video signals are 
converted to 1080/60i, 1080/25p video signals are to 
1080/50i, and then output.

• When you play back an HDV-formatted tape with 

copyright protected signals or input HDV signals with 
copyright protection to the   HDV/DV jack, pictures 
may be output in either 480i (NTSC) or 576i (PAL) 
format, regardless of the setting of [HDMI/CMPNT] 
of [VIDEO OUT] in the [IN/OUT REC] menu.

• The output level of the COMPONENT OUT jacks is as 

follows: 
Output at 480i (NTSC)
With [BETACAM] selected in [480i LEVEL] of the 
[IN/OUT REC] menu

Y: 1.0 Vp-p
(with 0.286 Vp-p sync negative,
output impedance 75 

Ω (ohms), unbalanced)

Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 

Ω (ohms), unbalanced)

(75% color bars with 7.5 IRE setup)

With [SMPTE] selected in [480i LEVEL] of the [IN/
OUT REC] menu

Y: 1.0 Vp-p
(with 0.3 Vp-p sync negative,
output impedance 75 

Ω (ohms), unbalanced)

Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 

Ω (ohms), unbalanced)

(100% color bars with no setup)

Output with other settings 

Y:  1.0 Vp-p
(output impedance 75 

Ω (ohms), unbalanced)

Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 

Ω (ohms), unbalanced)

(100% color bars with no setup)
480i/480p:
Y:  with 0.3 Vp-p sync negative
1080i/720p:
Y/Pb/Pr: with 0.6 Vp-p 3-level sync

f

Use this jack to output HDMI signals. HDMI OUT jack 
outputs both pictures and audio. To connect a device 
equipped with HDMI input connector, use the HDMI 
OUT jack on the unit.
The HDMI OUT jack outputs high-quality video with 
even less signal deterioration in quality than the 
COMPONENT OUT jacks.
You can set the output video format by using [HDMI/
CMPNT] of [VIDEO OUT] in the [IN/OUT REC] 
menu.
Text data is superimposed on a monitor in the same way 
as with a COMPONENT OUT jacks connection (page 
23).