Листовка для Panasonic GP-MF852PT
PREPARATIONS
SYSTEM CONNECTIONS
EXTERNAL SYNCHRONIZATION
1. Power Supply for Camera
Prepare a regulated DC power supply which
can supply DC 12 V ±10 % DC 465 mA or
more current and rated CLASS 2.
can supply DC 12 V ±10 % DC 465 mA or
more current and rated CLASS 2.
2. Lenses
Be sure to use the optional manual iris lens
having the following items.
Focus : Adjustable
Lens Weight : Less than 300
having the following items.
Focus : Adjustable
Lens Weight : Less than 300
g (0.66 lbs.)
Note:
If the lens is heavier than 300
g (0.66
lbs.), both the lens and the camera
should be secured by using the support-
er.
should be secured by using the support-
er.
Mount : C-mount
The protrusion at the rear of the lens should
be as shown in the illustration.
The protrusion at the rear of the lens should
be as shown in the illustration.
Less than 7.5 mm (1/2”)
Pick-up Device :
Inter Line Transfer type CCD with 768 (H) x 494 (V) pixels.
Image Size :
2/3” (7.95 (H) x 6.45 (V) mm)
Full non interlace (1/60 s)
Full non interlace (1/60 s)
Synchronization :
Internal or External (Selectable Automatically)
Internal : Built-in sync generator
External : 4.0 V[p-p]/75
Internal : Built-in sync generator
External : 4.0 V[p-p]/75
Ω
Horizontal drive and Vertical drive pulses
External Reset :
External signal (4.0 V[p-p]/75
Ω
, negative) supplied to EXT VD IN
connector can be used as reset signal
Horizontal Resolution :
500 lines at center
Minimum Illumination :
5 lx (0.5 foot-candles), (F1.4, Gain (+6 dB) ,
γ
OFF)
Gamma :
1.0
Gain Selection :
0/+6 dB
Electronic Shutter :
9-step (1/100 s to 1/30 000 s) at normal
5-step (1/2 000 s to 1/30 000 s) at Shutter Trigger
5-step (1/2 000 s to 1/30 000 s) at Shutter Trigger
Lens Mount :
C-Mount
Vibration Resistance :
7 G (10 Hz - 150 Hz) (2 hours each for three axes)
Shock Resistance :
80 G (IEC 68) *IEC=International Electronical Technical Commission
Power Source :
DC + 12 V, 465 mA
Ambient Temperature :
−
10˚C - +50˚C (14˚F - 122˚F)
Dimensions :
45(W) x 45(H) x 120(D) mm [1-25/32”(W) x 1-25/32”(H) x 4-23/32”(D)]
Weight :
270
g (0.6 lbs.) (Camera Only)
Dimensions and weight indicated are approximate values.
Specifications are subject to change without notice.
Specifications are subject to change without notice.
SPECIFICATIONS
OPTIONAL ACCESSORIES
Camera Cable
GP-CA34
GP-CA33
GP-CA59
GP-CA60
GP-CA33
GP-CA59
GP-CA60
3. Switch Covers Removal
Caution:
The following preparation should be
made by qualified service personnel or
system installers.
system installers.
For setting the Rear Panel Switch No.1 to 8,
remove the switch cover fixing screw on the
rear panel as shown below.
remove the switch cover fixing screw on the
rear panel as shown below.
VIDEO
Remove
this screw
this screw
Caution:
Keep the power switches of all units to OFF before connections.
1. Connect the optional camera cable GP-CA34 between the connector of this camera and the 12 V DC
Class 2 power supply(not provided as an accessory).
2. Connect the video connector of the GP-CA34 to the Frame Grabber.
Camera
Video input of
Frame Grabber
Frame Grabber
GP-CA34
HD IN
VD/V reset
Caution:
Use a 12 V DC Class 2
Power Supply only
12V DC
Power Supply
Full non interlace
The GP-MF852PT works in full non interlace mode
when external HD/VD signal is supplied to pin-6
and pin-7 of the camera connector (12-pin).
when external HD/VD signal is supplied to pin-6
and pin-7 of the camera connector (12-pin).
Notes:
• If the picture appears disturbed, be sure to
match the phases of falling edges of the
external HD/VD.
external HD/VD.
• Normal monitor cannot display the picture
from this camera. To display the picture, syn-
chronize the camera and multiscan monitor
from external HD/VD.
chronize the camera and multiscan monitor
from external HD/VD.