Справочник Пользователя для Ingersoll-Rand VL2-030
MHD56012 - Edition 8
3
WARNING TAG
Each hoist is supplied from the factory with the warning tag
shown. If tag is not attached to your unit, order a new tag and
install it. Refer to the parts list for the part number. Read and obey
all warnings and other safety information attached to this hoist.
Tag may be shown smaller than actual size.
shown. If tag is not attached to your unit, order a new tag and
install it. Refer to the parts list for the part number. Read and obey
all warnings and other safety information attached to this hoist.
Tag may be shown smaller than actual size.
SAFE OPERATING INSTRUCTIONS
The following warnings and operating instructions have been
adapted in part from American National Standard ASME B30.16
and are intended to avoid unsafe operating practices which might
lead to injury or property damage.
adapted in part from American National Standard ASME B30.16
and are intended to avoid unsafe operating practices which might
lead to injury or property damage.
Ingersoll-Rand recognizes that most companies who use hoists
have a safety program in force in their plants. In the event that
some conflict exists between a rule set forth in this publication and
a similar rule already set by an individual company, the more
stringent of the two should take precedence.
have a safety program in force in their plants. In the event that
some conflict exists between a rule set forth in this publication and
a similar rule already set by an individual company, the more
stringent of the two should take precedence.
Safe Operating Instructions are provided to make an operator
aware of dangerous practices to avoid and are not necessarily
limited to the following list. Refer to specific sections in the
manual for additional safety information.
aware of dangerous practices to avoid and are not necessarily
limited to the following list. Refer to specific sections in the
manual for additional safety information.
1.
Only allow personnel trained in safety and operation to
operate hoist.
operate hoist.
2.
Only operate a hoist if you are physically fit to do so.
3.
When a “DO NOT OPERATE” sign is placed on hoist, do
not operate hoist until sign has been removed by designated
personnel.
not operate hoist until sign has been removed by designated
personnel.
4.
Before each shift, the operator should inspect hoist for wear
or damage.
or damage.
5.
Never use a hoist which inspection indicates is worn or
damaged.
damaged.
6.
Periodically, inspect hoist thoroughly and replace worn or
damaged parts. Refer to “INSPECTION” section.
damaged parts. Refer to “INSPECTION” section.
7.
Lubricate hoist regularly. Refer to “LUBRICATION”
section.
section.
8.
Do not use hoist if hook latch has been sprung or broken.
9.
Check that hook latches are engaged before using.
10. Never splice a hoist chain by inserting a bolt between links.
11. Only lift loads less than or equal to rated capacity of hoist.
11. Only lift loads less than or equal to rated capacity of hoist.
Refer to “SPECIFICATIONS” section.
12. Never use the hoist chain as a sling.
13. Never operate a hoist when load is not centered under top
hook. Do not “side pull” or “yard.”
14. Never operate a hoist with twisted, kinked, “capsized” or
damaged load chain.
15. Do not force a chain or hook into place by hammering.
16. Never insert point of hook into a chain link.
17. Be certain load is properly seated in saddle of hook, and hook
16. Never insert point of hook into a chain link.
17. Be certain load is properly seated in saddle of hook, and hook
latch is engaged.
18. Do not support load on tip of hook.
19. Never run load chain over a sharp edge. Use a sheave.
20. When using two hoists to suspend one load, select two hoists
19. Never run load chain over a sharp edge. Use a sheave.
20. When using two hoists to suspend one load, select two hoists
each having a rated capacity equal to or more than the load.
This provides adequate safety in the event of a sudden load
shift.
This provides adequate safety in the event of a sudden load
shift.
21. Pay attention to the load at all times when operating hoist.
22. Always ensure that you, and all other people, are clear of load
22. Always ensure that you, and all other people, are clear of load
path. Do not lift a load over people.
23. Never use hoist for lifting or lowering people, and never
allow anyone to stand on a suspended load.
24. Ease slack out of chain and sling when starting a lift. Do not
jerk load.
25. Do not swing a suspended load.
26. Do not leave a load suspended when hoist is unattended or
26. Do not leave a load suspended when hoist is unattended or
not in use.
27. Never weld or cut a load suspended by the hoist.
28. Never use hoist chain as a welding electrode.
29. Do not operate hoist if chain jumping, excessive noise,
28. Never use hoist chain as a welding electrode.
29. Do not operate hoist if chain jumping, excessive noise,
jamming, overloading or binding occurs.
30. Keep load from hitting load chain.
31. Only operate the hoist with manual power.
32. After use, or when in a non-operational mode, hoist should be
31. Only operate the hoist with manual power.
32. After use, or when in a non-operational mode, hoist should be
secured against unauthorized and unwarranted use.