Справочник Пользователя для Sony CA-590P
Internal Boards and Switch Settings
11
J S11/S12 switches
These switches select the audio to be mixed with the audio
output to the INCOM 1 connector.
These switches select the audio to be mixed with the audio
output to the INCOM 1 connector.
When a one ear headset is used, set the S11-3 and S11-4
switches to ON.
switches to ON.
K S13/S14 switches
These switches select the audio to be mixed with the
program audio output to the INCOM 1 connector.
These switches select the audio to be mixed with the
program audio output to the INCOM 1 connector.
When a one ear headset is used, set the S13-1 and S13-2
switches to ON.
switches to ON.
L S15 switch
Set according to the broadcast system.
OFF: NTSC (for the CA-590)
ON: PAL (for the CA-590P)
Set according to the broadcast system.
OFF: NTSC (for the CA-590)
ON: PAL (for the CA-590P)
c AU-294 board
A S3 switch
Set according to the microphone type of the headset
connected to the INCOM 2 connector.
DYN: Dynamic-type microphone
CM: Carbon-type microphone
Set according to the microphone type of the headset
connected to the INCOM 2 connector.
DYN: Dynamic-type microphone
CM: Carbon-type microphone
B S4 switch
Set to ON when an unbalanced-type headset is connected
to the INCOM 2 connector.
Set to ON when an unbalanced-type headset is connected
to the INCOM 2 connector.
C S5 switch
Sets the gain for the headset connected to the INCOM 2
connector.
+ : Sets the gain 6 dB above the standard level.
0 : Standard level.
– : Sets the gain 6 dB below the standard level.
Normally, set this switch to 0.
Sets the gain for the headset connected to the INCOM 2
connector.
+ : Sets the gain 6 dB above the standard level.
0 : Standard level.
– : Sets the gain 6 dB below the standard level.
Normally, set this switch to 0.
D S7 switch
When set to ON, the audio signal input from the
TRACKER connector is mixed to the imtercom audio and
When set to ON, the audio signal input from the
TRACKER connector is mixed to the imtercom audio and
output to the INCOM 2 connector. Normally, set this
switch to OFF (center position).
switch to OFF (center position).
E S8 switch
Specifies whether the VR of the INCOM 2 is used for
serial mix or parallel mix. Normally, set this switch to OFF.
Specifies whether the VR of the INCOM 2 is used for
serial mix or parallel mix. Normally, set this switch to OFF.
F S10 switch
This switch is used for the intercom system connected to
the INCOM 2 connector. Normally, set this switch to
NORM.
This switch is used for the intercom system connected to
the INCOM 2 connector. Normally, set this switch to
NORM.
G S11/S12 switches
These switches select the audio to be mixed with the audio
output to the INCOM 2 connector.
These switches select the audio to be mixed with the audio
output to the INCOM 2 connector.
Switch
Audio to be mixed
Normal setting
S11-1
Audio from INCOM 1
ON
S11-2
Audio from INCOM 2
OFF
S11-3
Program audio 1
OFF
S11-4
Program audio 2
OFF
S12
Tracker audio
ON
Switch
Audio to be mixed
Normal setting
S13-1
Audio from INCOM 1
OFF
S13-2
Audio from INCOM 2
OFF
S13-3
Program audio 1
ON
S13-4
Program audio 2
ON
S14
Tracker audio
OFF
S10
S201
S3
S4
S5
S101
S7
S8
S251
S252
S253
S252
S253
S13
S14
S14
S11
S12
S12
H S13/S14 switches
F S10 switch
I S101 switch
E S8 switch
B S4 switch
A S3 switch
G S11/S12 switches
K S251/S252 switches
D S7 switch
L S253 switches
J S201 switches
C S5 switch
C S5 switch
Switch
Audio to be mixed
Normal setting
S11-1
Audio from INCOM 1
OFF
S11-2
Audio from INCOM 2
ON
S11-3
Program audio 1
OFF