Справочник Пользователя для Panasonic PV-GS300

Скачать
Страница из 88
Others
70
LSQT0974
• Is the cassette cover open? If the cover is 
open, the Camcorder may not operate 
normally. Close the cassette cover. (
2: The screen has changed suddenly.
• Has the demonstration started? In the Tape 
Recording mode, if you set [DEMO MODE] >> 
[ON] without inserting a cassette and a card, 
the demonstration starts. For normal use, set 
this function to [OFF]. (
3: A cassette cannot be inserted.
• Has condensation occurred? Wait until the 
condensation indication disappears.
4: Auto focus function does not work.
• Is manual focus mode selected? If auto focus 
mode is selected, focus is automatically 
adjusted.
• There are some recording subjects and 
surroundings for which the auto focus does not 
operate correctly. (
) If so, use the manual 
focus mode to adjust the focus. (
)
• Is the MagicPix function set? When the 
MagicPix function is working, focusing shifts 
into the manual mode.
5: The Camcorder arbitrarily stops recording.
• Is the AGS function activated? Record in the 
normal horizontal position or set [AGS] to 
[OFF].(
Indications
1: A sentence is displayed in red in the screen 
center.
• Read the contents and respond to them. (
)
2: The time code becomes inaccurate.
0 The time code indication counter may not be 
constant in the reversed slow-motion playback, 
but this is not a malfunction.
3: The remaining tape time indication 
disappears.
• The remaining tape time indication may 
disappear temporarily during frame-by-frame 
playback or other operation. If you continue 
ordinary recording or playback, the indication is 
restored.
4: The remaining tape time Indication does not 
match the actual remaining tape time.
• If scenes of less than 15 seconds are 
continuously recorded, the remaining tape time 
cannot be correctly displayed.
• In some cases, the remaining tape time 
indication may show remaining tape time that is 
2 to 3 minutes shorter than the actual 
remaining tape time.
5: A function indication such as mode 
indication, remaining tape time indication, 
or time code indication is not shown.
• If you set [SETUP] >> [DISPLAY] >> [OFF], 
indications other than the tape running 
condition, warning, and date indications 
disappear.
Playback (Sound) 
1: Sound is not played back from the built-in 
speaker of the Camcorder.
0 Is the volume too low? During playback, push 
the [
s
/VOL
r] lever to display the volume 
indication and adjust it. (
2: Different sounds are reproduced at the 
same time.
• Have you set [SETUP] >> [12bit AUDIO] >> 
[MIX]? If you set [AUDIO REC] >> [12bit] and 
dub audio to a recorded tape, you can hear the 
sound on recording and the sound dubbed at a 
later time. To hear the sounds separately, set 
to [ST1] or [ST2]. (
• Have you set [SETUP] >> [AUDIO OUT] >> 
[STEREO] and reproduced a picture containing 
the main sound and sub sound? Set to [L] to 
hear main sound, and set to [R] to hear the sub 
sound. (
3: Audio dubbing cannot be performed.
• Is the accidental erasure prevention slider on 
the cassette open? If it is open (set to [SAVE]), 
audio dubbing cannot be performed. (
• Are you attempting to edit a tape portion that 
was recorded in LP mode? LP mode does not 
allow audio dubbing. (
4: The original sound was erased when audio 
dubbing was performed.
• If you perform audio dubbing on a recording made 
in [16bit] mode, the original sound will be erased. 
If you wish to preserve the original sound, be sure 
to select [12bit] mode when recording. 
5: Sounds cannot be played back.
• Although a cassette with no audio dubbing is 
being played, have you set [SETUP] >> 
[12bit AUDIO] >> [ST2]? To play back a 
cassette with no audio dubbing, set 
[12bit AUDIO] >> [ST1].(
• Is the variable speed search function working? 
Press the [VAR SEARCH] button on the 
remote control to cancel the variable speed 
search function. (
Playback (Pictures) 
1: Although the Camcorder is correctly connected 
to a TV, playback images cannot be seen.
The playback images are vertical.
• Have you selected video input on the TV? 
Please read the operating instructions of your 
TV and select the channel that matches the 
input terminals used for the connection.
• Is the [TV ASPECT] setting correct? Change 
the setting to match the aspect ratio of the TV. 
[SETUP] >> [TV ASPECT] >> [16:9] or [4:3].
2: Mosaic-pattern noise appears on images 
during cue or review playback.
• This phenomenon is characteristic of digital 
video systems. It is not a malfunction.
3: Horizontal stripes appear on images during 
cue and review playback.
• Horizontal stripes may appear depending on 
the scene, but this is not a malfunction.
LSQT0974_ENG.book  70 ページ  2005年11月7日 月曜日 午前11時58分