Справочник Пользователя для Panasonic AG-HPX370P
44
Chapter
Recording
and
Pla
ybac
Pla
ybac
k
Loop recording (LOOP REC)
• When two P2 cards are inserted in the P2 card slots,
each card is recorded in succession.
• When there is no longer any space left on the cards,
recording starts over from the first card by recording new
clips over saved old clips.
clips over saved old clips.
For the clip recording time, see [Splitting clips recorded
on P2 cards] (page 33).
on P2 cards] (page 33).
B
A
B
C
Recordingwillbemadeontheareaswithnorecording
consecutively(A,B,thenC).Whenallareasonallcardsare
recorded,newrecording(C)willbemadebyoverwritingthe
areaA.
Beforestarting
looprecording
Firstloop
recording
Secondloop
recording
Recordingstart
1stcard
ndcard
Norecording
Recorded
1
CheckthattheSYSTEMSETUPscreenisset
upasdescribedonpage4.
upasdescribedonpage4.
For details on menu operation, refer to [Using the
menus] (page 129).
menus] (page 129).
2
SelectLOOPinthemenuoptionREC
FUNCTIONintheRECORDINGSETUP
screen.
FUNCTIONintheRECORDINGSETUP
screen.
3
PresstheRECbutton.
• Recording starts.
• Press the REC button to stop recording.
• To cancel this function, turn the camera off or
• Press the REC button to stop recording.
• To cancel this function, turn the camera off or
select NORMAL in the REC FUNCTION item.
• The following indications appear to the left of the
operation status display.
• During recording: “L-REC” stays lit.
• During a pause: “L-PAUSE” stays lit.
• When remaining memory is low: “P2 LACK L-”
• During a pause: “L-PAUSE” stays lit.
• When remaining memory is low: “P2 LACK L-”
blinks.
NOTE
• Use two P2 cards with at least one minute of
remaining recording time.
• The mode check screen shows standard recording
time depending on recording format as remaining P2
card time. When loop recording is stopped right after
deleting old data, the time of recordings on the card
may be shorter than indicated.
card time. When loop recording is stopped right after
deleting old data, the time of recordings on the card
may be shorter than indicated.
• This function is not available during IEEE1394 input.
• The pre-recording and one-clip recording functions
• The pre-recording and one-clip recording functions
are not available.
• Canceling this function may take some time. The
succeeding operations are not available until the P2
CARD ACCESS LED goes from blinking to steady
lighting.
CARD ACCESS LED goes from blinking to steady
lighting.
• During loop recording, the access LEDs for all P2
cards used in the recording light orange or blinks.
Note that removing any of the P2 cards will terminate
loop recording.
Note that removing any of the P2 cards will terminate
loop recording.
• Irregularity in the input GENLOCK reference signal
during loop recording may terminate recording.
One-clip recording (ONE CLIP REC)
Instead of creating a new clip for each recording session
(i.e., operation from REC start to stop), this mode compiles
images from multiple recording sessions into a single clip.
(i.e., operation from REC start to stop), this mode compiles
images from multiple recording sessions into a single clip.
*
First Recording
Second Recording
Nth Recording*
REC Start
REC Start
REC Start
REC stop
REC stop
REC stop
Single Combined Clip
Up to a maximum of 99 recordings can be combined into
a single clip. When the 99th recording ends, recordings
are no longer automatically combined into the same clip.
Subsequent recordings are combined into a new clip.
To use this function, set the menu option ONE CLIP REC to
ON in the RECORDING SETUP screen.
When one-clip recording mode is enabled, “1-CLIP”
appears in the viewfinder and at the top of the LCD monitor.
When you press the REC button on the camera to start your
first recording, “START 1
ON in the RECORDING SETUP screen.
When one-clip recording mode is enabled, “1-CLIP”
appears in the viewfinder and at the top of the LCD monitor.
When you press the REC button on the camera to start your
first recording, “START 1
CLIP” appears.
Any subsequent recordings are automatically combined
into the clip. Up to a maximum of 99 clips can be
combined into a single clip.
into the clip. Up to a maximum of 99 clips can be
combined into a single clip.
To record a new clip
Follow the instructions below to use a new and separate
clip and end combining to the clip.
clip and end combining to the clip.
Press and hold the STOP button for about 2 seconds
while recording is paused. (operating while recording is
on standby)
while recording is paused. (operating while recording is
on standby)
Or
Press and hold the REC button for about 2 seconds
to stop recording. (operating while recording is in
progress)
to stop recording. (operating while recording is in
progress)
Follow the instructions above to end combining to the clip.
“END 1-CLIP” displays. Subsequent recordings use a new
and separate clip.
“END 1-CLIP” displays. Subsequent recordings use a new
and separate clip.
NOTE
• In addition to the aforementioned steps, the following ends
combining to the clip and subsequent recordings use a new
clip.
clip.
• When the power is turned off
• When the P2 card with the previous recording is removed
• When the P2 card is formatted or the clip is deleted (when
• When the P2 card with the previous recording is removed
• When the P2 card is formatted or the clip is deleted (when
the previous combined clip does not exist)