Справочник Пользователя для Sony PMW-320K
Basic Operations
69
Ch
apt
apt
er 4
S
hoo
tin
g
g
- Press the REC START button (see
- Press the VTR button on the lens (see
- Turn on the assignable switch to which the
Rec function has been assigned (see
page 130).
page 130).
During recording, the TALLY indicators, the
tally indicator on the front panel of the
viewfinder, and the REC indication on the
viewfinder screen light. Adjust the zoom and
focus as required.
tally indicator on the front panel of the
viewfinder, and the REC indication on the
viewfinder screen light. Adjust the zoom and
focus as required.
Notes
• Never remove the battery pack while the
camcorder is recording (while an ACCESS lamp
is lit). Doing so risks the loss of several seconds
of data before the recording was interrupted,
because internal processing will not end
normally.
is lit). Doing so risks the loss of several seconds
of data before the recording was interrupted,
because internal processing will not end
normally.
• The playback control buttons (EJECT, F REV, F
FWD, NEXT, PREV, PLAY/PAUSE, STOP) do
not function during recording.
not function during recording.
10
To stop recording, perform one of the
operations listed in step
operations listed in step
9
.
The TALLY indicators, the tally indicator on
the front panel of the viewfinder, and the
REC indication on the viewfinder screen go
out, and camcorder enters recording standby
(STBY) mode.
A clip is created from the video and audio
data and the metadata recorded between steps
the front panel of the viewfinder, and the
REC indication on the viewfinder screen go
out, and camcorder enters recording standby
(STBY) mode.
A clip is created from the video and audio
data and the metadata recorded between steps
9
and
10
.
To check the recording (recording review)
With the camcorder in recording standby
(STBY) mode, turn on the assignable switch
to which the Rec Review function or the
Freeze Mix function has been assigned (see
page 129).
The camcorder plays the entire last clip, or
the last few seconds of that clip (3 seconds or
10 seconds), and then returns to standby
mode.
You can use MAINTENANCE >Camera
Config >Rec Review in the setup menu (see
page 121) to change the playback time.
When the Rec Review function is assigned to
the RET button on the lens, you can also
conduct a review by using the RET button.
With the camcorder in recording standby
(STBY) mode, turn on the assignable switch
to which the Rec Review function or the
Freeze Mix function has been assigned (see
page 129).
The camcorder plays the entire last clip, or
the last few seconds of that clip (3 seconds or
10 seconds), and then returns to standby
mode.
You can use MAINTENANCE >Camera
Config >Rec Review in the setup menu (see
page 121) to change the playback time.
When the Rec Review function is assigned to
the RET button on the lens, you can also
conduct a review by using the RET button.
11
Repeat steps
9
and
10
to continue
recording.
With each repetition, another clip is created
on the memory card.
on the memory card.
Notes
• You cannot resume recording for about one second
after stopping recording.
• The maximum number of clips that can be recorded on
one memory card is 600. Even if the memory card has
enough free capacity to record more clips, when 600
clips have been recorded, no further recording is
possible.
enough free capacity to record more clips, when 600
clips have been recorded, no further recording is
possible.
Clip file sizes
The XDCAM EX-series products limit the
maximum file size of an HD clip to 4 GB and that
of an SD clip to 2 GB.
If you continue recording for an extended period,
recorded materials may be segmented into
multiple files, depending on the file size (the
maximum number of partitions is 99).
The camcorder regards continuous recording as
one clip even if it has been segmented into
multiple files.
The XDCAM EX-series products limit the
maximum file size of an HD clip to 4 GB and that
of an SD clip to 2 GB.
If you continue recording for an extended period,
recorded materials may be segmented into
multiple files, depending on the file size (the
maximum number of partitions is 99).
The camcorder regards continuous recording as
one clip even if it has been segmented into
multiple files.
Clip names
Eight-character clips names (consisting of a four-
character prefix and a four-digit number) are
generated automatically for clips recorded by this
camcorder.
Example: ABCD0001
You can also use OPERATION >Clip >Title
Prefix (see page 107) in the setup menu to set the
clip name prefix to a user-specified string of
characters (four to 46 characters in length). (A
user-specified prefix cannot be changed after
recording.)
The four-digit number at the end of clip names is
generated automatically, counting up in order as
clips are recorded.
Eight-character clips names (consisting of a four-
character prefix and a four-digit number) are
generated automatically for clips recorded by this
camcorder.
Example: ABCD0001
You can also use OPERATION >Clip >Title
Prefix (see page 107) in the setup menu to set the
clip name prefix to a user-specified string of
characters (four to 46 characters in length). (A
user-specified prefix cannot be changed after
recording.)
The four-digit number at the end of clip names is
generated automatically, counting up in order as
clips are recorded.
When the camcorder is in standby (STBY) mode,
you can play all or part of the most recently
recorded clip (see page 69).
you can play all or part of the most recently
recorded clip (see page 69).
Playing Recorded Clips
Clip 1
Clip 2
Clip 3