Справочник Пользователя для First Alert FA168CPS

– 2 – 

Local programming requires the use of an alpha keypad connected to the keypad terminals on the control. 
A.  POWER UP, then depress [

✱] and [#]  both at once, within 50 seconds of powering up (if ✱98 was used to exit program 

mode, this method must be used to reenter program mode). 

 OR 
B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0. 

DATA FIELD PROGRAMMING PROCEDURES 

Press [

∗] + [Field Number], followed by the required entry.  

When the desired field number appears, simply make the required entry. When the last entry for a 
field is entered, the keypad beeps three times and automatically displays the next data field in 
sequence. 
If the number of digits that you need to enter in a data field is less than the maximum digits available 
(for example, the phone number fields *41, *42), enter the desired data, then press [

∗ ] to end the 

entry. The next data field number is displayed. 

Review a Data Field  Press [#] + [Field Number].  

Data will be displayed for that field number. No changes will be accepted in this mode. 

Deleting an Entry Press 

[

∗] + [Field Number] + [∗]. (Applies only to fields ∗40 thru *46, *94, and pager programming 

fields) 

∗56, ∗57, ∗58, ∗79, ∗80, ∗81, ∗82, ∗187) 

Press [

✱] + [Interactive Mode No.] (for example, ✱56). The alpha display keypad will display the first of a series of prompts 

requesting entries.  
Interactive Mode 

Used to Program 

✱56 Zone Programming 

Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RF 
transmitters. 

✱57 Function Key Programming  Unlabeled keypad keys (known as ABCD keys) for special functions 
✱58 Zone Programming 

Same options as *56 mode, but with fewer prompts. Intended for those familiar with  

(Expert mode) 

this type of programming, otherwise *56 mode is recommended. 

✱79 Output Device Mapping 

Assign module addresses and map individual relays/powerline carrier devices 

✱80 Output Programming 

4229 or 4204 Relay modules, Powerline Carrier devices, or on-board triggers 

✱81 Zone List Programming 

Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc. 

✱82 Alpha Programming 

Zone alpha descriptors 

✱96  Initializes download ID and subscriber account number. 

✱97  Sets all data fields to original factory default values. 
 

✱98  Exits programming mode and prevents  re-entry by:  Installer Code + 8 + 0 + 0.  If ✱98 is used to exit programming 

mode, system must be powered down, and method A above used to enter the programming mode. 

 

See field *88 for other *98 Program mode lockout options. 

 

✱99  Exits programming mode and allows  re-entry by: Installer Code + 8 + 0 + 0 or method 1 above. 

 

OC = OPEN CIRCUIT (no communication between Keypad and Control). 

EE or ENTRY ERROR = ERROR (invalid field number entered;  re-enter valid field number). 

After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds. 
This will revert to a “Ready” message in approximately 1 minute, which allows PIRS, etc. to stabilize. You can bypass this 
delay by pressing [#] + [0].  

If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after 
you correct the programming.