Справочник Пользователя для Bosch ICP-CC404
ICP-CC404 | Installation Guide | 12.0 Dialer Options
50 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
The options are:
1 – Display FAULT Indicator When the Telephone
Line Fails
Line Fails
When this options is selected, the FAULT indicator
flashes and the codepad buzzer beeps once per
minute if the control panel detects that the telephone
line is disconnected. Refer to Section 4.13 Fault
Descriptions on page 22 for more information.
flashes and the codepad buzzer beeps once per
minute if the control panel detects that the telephone
line is disconnected. Refer to Section 4.13 Fault
Descriptions on page 22 for more information.
2 – Sound Alarm When System Is Armed
To use Option 2, you must also select Option 1. If the
control panel detects that the telephone line is
disconnected when the system is armed, the horn
speaker, bell, and strobe outputs are activated.
control panel detects that the telephone line is
disconnected when the system is armed, the horn
speaker, bell, and strobe outputs are activated.
4 – Sound Alarm when System Is Disarmed
You must also select Option 1 to use this option. If
the control panel detects that the telephone line is
disconnected when the system is disarmed, the horn
speaker, bell, and strobe outputs are activated.
the control panel detects that the telephone line is
disconnected when the system is disarmed, the horn
speaker, bell, and strobe outputs are activated.
If you program 7 in this location, the horn
speaker, bell, strobe, and EDMSAT
outputs are all activated when the system
is armed or disarmed.
speaker, bell, strobe, and EDMSAT
outputs are all activated when the system
is armed or disarmed.
8 – Reserved
12.0 Dialer Options
When programming these locations, there are up to
four options per location. You can select any
combination of the options by programming a single
value. Calculate this value by adding the option bit
numbers together. Refer to Section 2.3 Programming
Option Bits on page 10 for more information.
four options per location. You can select any
combination of the options by programming a single
value. Calculate this value by adding the option bit
numbers together. Refer to Section 2.3 Programming
Option Bits on page 10 for more information.
12.1 Dialer Options 1
Program the selected Dialer Options 1 in
Location
177.
The default value is
9.
The options are:
1 – Dialer Reporting Functions Allowed
If you select this option, the dialer operates for all
functions.
functions.
If you do not select this option, the communication
dialer does not operate.
dialer does not operate.
Upload/Download using the CC816 Alarm Link
Software and telephone remote arming remain
operational regardless of this setting.
Software and telephone remote arming remain
operational regardless of this setting.
2 – Remote Arming by Telephone Allowed
If you select this option, you can remotely arm the
system using a standard telephone with the CC911
Phone Controller or by pressing [*] on your touch-
tone telephone. Refer to Section 7.0 Remote Arming by
Telephone on page 38 for more information. Forced
arming is automatically assumed when this feature is
used. Refer to Section 14.3.6 Zone Options 2 on page 58
for more information on forced arming.
system using a standard telephone with the CC911
Phone Controller or by pressing [*] on your touch-
tone telephone. Refer to Section 7.0 Remote Arming by
Telephone on page 38 for more information. Forced
arming is automatically assumed when this feature is
used. Refer to Section 14.3.6 Zone Options 2 on page 58
for more information on forced arming.
Remote arming by telephone is not affected by
whether remote functions are enabled or disabled.
Refer to Section 11.10 Ring Count on page 49 for
programming the number of rings before the control
panel answers an incoming call.
whether remote functions are enabled or disabled.
Refer to Section 11.10 Ring Count on page 49 for
programming the number of rings before the control
panel answers an incoming call.
4 – Answering Machine Bypass Only When Armed
Select this option to enable the Answering Machine
Bypass feature when the system is armed. When the
system is disarmed, the control panel does not answer
any incoming calls. This option is useful in high
telephone traffic installations where the control panel
could answer an incoming call. Refer to Section 11.10
Ring Count on page 49 to program Answering
Machine Bypass.
Bypass feature when the system is armed. When the
system is disarmed, the control panel does not answer
any incoming calls. This option is useful in high
telephone traffic installations where the control panel
could answer an incoming call. Refer to Section 11.10
Ring Count on page 49 to program Answering
Machine Bypass.
8 – Use Bell 103 for FSK Format (Disabled = CCITT
V21)
V21)
If this option is selected, the control panel uses the
BELL 103 transmission frequency at 300 baud. If this
option is not selected, the control panel uses the
CCITT V21 transmission frequency at 300 baud.
BELL 103 transmission frequency at 300 baud. If this
option is not selected, the control panel uses the
CCITT V21 transmission frequency at 300 baud.
12.2 Dialer Options 2
Program the selected Dialer Options 2 in
Location
178.
The default value is
0.
The options are:
1 – Open/Close Reports Only if Previous Alarm
When selected, an Opening Report is sent to the base
station receiver when the system is disarmed after an
alarm occurred. When the system is armed, a Closing
Report is sent. An Opening or Closing Report is not
sent again until the system registers another alarm.
station receiver when the system is disarmed after an
alarm occurred. When the system is armed, a Closing
Report is sent. An Opening or Closing Report is not
sent again until the system registers another alarm.
Open/Close Reports must be enabled in Locations
333 and 334 (refer to Section 15.6 Open/Close Reports on
page 61) for this option to work.
333 and 334 (refer to Section 15.6 Open/Close Reports on
page 61) for this option to work.
If the system is disarmed when an alarm
occurs, only a Closing Report is sent the
next time the system is armed.
occurs, only a Closing Report is sent the
next time the system is armed.
2 – Open/Close Reports for STAY Mode 1 and
STAY Mode 2
STAY Mode 2
Select this option if Open and Close Reports are
required when the system is armed in STAY Mode 1
or STAY Mode 2.
required when the system is armed in STAY Mode 1
or STAY Mode 2.