Справочник Пользователя для Vermont Casting DV360

3

This gas appliance should be installed by a qualified installer in 
accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Appliances and 
Equipment.  If the unit is being installed in a mobile home, the 
installation should comply with the current CAN/CSA Z 240.4 
code. For U.S.A Installations follow local codes and/or the cur-
rent National Fuel Gas Code. ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings and 
installation of this appliance shall be done by a licensed 
gas fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION PLEASE 
NOTE THE FOLLOWING:
1 .  This fireplace gives off high temperatures and should be 

located out of high traffic areas and away from furniture and 
draperies.

2.   Children and adults should be alerted to the hazards of the 

high surface temperatures of this fireplace and should stay 
away to avoid burns or ignition of clothing.

3.   Children should be carefully supervised when in the same 

room as your fireplace.

4.   Under no circumstances should this fireplace be modified. 

Parts removed for servicing should be replaced prior to 
operating this fireplace again.

5.  Installation and any repairs to this fireplace must be per-

formed by a qualified installer, service agency or gas sup-
plier. A professional service person should be contacted to 
inspect this fireplace annually. Make it a practice to have 
all of your gas fireplaces checked annually. More frequent 
cleaning may be required due to excess lint and dust from 
carpeting, bedding material, etc.

6.  Control compartments, burners and air passages in this fire-

place should be kept clean and free of dust and lint. Make 
sure the gas valve and pilot light are turned off before you 
attempt to clean this fireplace.

7.  The venting system (chimney) of this fireplace should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your fireplace clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stocking or decorations be hung in 
the area of it.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10. The flow of combustion and ventilation air must not be ob-

structed in any way. 

11. When fireplace is installed directly on carpeting, vinyl tile 

or any combustible material other than wood, this fireplace 
must be installed on a metal or wood panel extending the full 
width and depth of the fireplace.

12. This fireplace requires adequate ventilation and combustion 

air to operate properly.

13. This fireplace must not be connected to a chimney flue serv-

ing a separate solid fuel burning fireplace.

14. When the fireplace is not in use it is recommended that the 

gas valve be left in the OFF position.

Proposition 65 Warning: Fuels used in gas, woodburning or 
oil fired appliances, and the products of combustion of such 
fuels, contain chemicals known to the State of California to 
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6

Remove any plastic from trim parts before turning the 
fireplace ON.
It is normal for fireplaces fabricated of steel to give off 
some expansion and/or contraction noises during the 
start up or cool down cycle. Similar noises are found 
with your furnace heat exchanger or car engine.  It is 
not unusual for your CFM Corporation gas fireplace to 
give off some odor the first time it is burned. This is due 
to the manufacturing process.

It is recommended that you burn your fireplace for at 
least ten (10) hours the first time you use it. If the op-
tional fan kit has been installed, place the fan switch in 
the “OFF” position during this time.

Y

E

A

B

C

D

F

Y

B

X

LU584-1

Locating unit

2/4/99   djt

LU584-1

A) Flat on wall  

B) Cross corner 

C)  **Island

D) *Room divider  E) *Flat on wall corner 

F)   Chase installation

Y) 6” minimum
Note (Fig. 1):  
** Island (C) and Room Divider (D) installation is possible as long as 
the horizontal portion of the vent system (X) does not exceed 20’ (6 m).  
See details in Venting Section.
*  When you install your fireplace in(D) Room divider or (E) Flat on wall 
corner positions (Y), a minimum of 6“ (152 mm) clearance must be 
maintained from the perpendicular wall and the front of the fireplace.

Fig. 1  Locating gas fireplace.