Справочник Пользователя для Vermont Casting DV360
7
DV360/580 Series Direct Vent Gas Fireplace
20010667
Framing And Finishing
Check fireplace to make sure it is levelled
and properly positioned.
and properly positioned.
To mount the appliance: Choose the location.
DV360 (Fig. 5)
1. This unit comes with four (4) flanges pre-mounted
DV360 (Fig. 5)
1. This unit comes with four (4) flanges pre-mounted
on both sides of the fireplace to allow two different
drywall thicknesses to be used. Flange “A” is for 1/2”
drywall while flange “B“ is for 5/8” drywall.
drywall thicknesses to be used. Flange “A” is for 1/2”
drywall while flange “B“ is for 5/8” drywall.
2. Bend the desired flanges out 90° on both sides of
the fireplace. Slide the fireplace into the framed
opening until the flanges contact the front surfaces
of the framing. Level the unit and secure it firmly in
place.
opening until the flanges contact the front surfaces
of the framing. Level the unit and secure it firmly in
place.
A
B
FP1539
flange location
12/04
Flange
Drywall
Position
Depth
A
1/2” / 13 mm
B
5/8” / 16 mm
Flange Location for
Desired Drywall Depth
FP1539
Fig. 5 Drywall flange location for DV360.
DV580 (Fig. 5a)
1. Nailing flanges are supplied with the fireplace (found
1. Nailing flanges are supplied with the fireplace (found
on the fireplace hearth). To level the box and secure
it firmly in place, remove the nailing flanges from
the hearth and install at the sides of the fireplace as
shown in Figure 5a.
it firmly in place, remove the nailing flanges from
the hearth and install at the sides of the fireplace as
shown in Figure 5a.
2. Screw through the slotted holes in the drywall strip
and into pre-drilled holes in fireplace side. Measure
from face of fireplace to the face of the drywall strip
to confirm the final depth.
from face of fireplace to the face of the drywall strip
to confirm the final depth.
Final Finishing
Noncombustible materials such as brick or tile can be
extended over the edges of the face of the fireplace.
Do not cover the window frame assembly, any vent,
louvre assembly top or louvre assembly bottom. If
a Trim Kit is to be installed, brick and tile will have to be
installed flush with the side of this appliance.
extended over the edges of the face of the fireplace.
Do not cover the window frame assembly, any vent,
louvre assembly top or louvre assembly bottom. If
a Trim Kit is to be installed, brick and tile will have to be
installed flush with the side of this appliance.
FP1023
side nailing flange
1/27/00 djt
A
B
C
Adjustable Drywall Strip
(Nailing Flange)
Flange
Drywall
Position
Depth
A
1/2” / 13 mm
B
5/8” / 16 mm
C
3/4” / 19 mm
Adjustable
1/2”, 5/8” & 3/4”
Spacing
FP1023
Fig. 5a Adjustable drywall strip (nailing flange) for DV580.
DV360 / DV580
Certified To
ANSI Z21.88-2005 / CSA 2.33-2005
Vented Gas Fireplace Heater
For units:
GFDN4L2, GFDE4L2, GFDI4L2, GFDL4L2
GFDN4P0, GFDE4P0, GFDI4P0
GFDN4L2, GFDE4L2, GFDI4L2, GFDL4L2
GFDN4P0, GFDE4P0, GFDI4P0
Gas Specifications
MAX.
MIN.
GAS
INPUT INPUT
MODEL
FUEL
CONTROL
B.T.U.H B.T.U.H.
DV360RN
Natural Gas
Millivolt Hi/Lo
30,000
18,500
DV360RP
Propane
Millivolt Hi/Lo
30,000
17,000
DV360EN
Natural Gas
24 Volt Hi/Lo
30,000
18,500
DV360EP
Propane
24 Volt Hi/Lo
30,000
20,000
DV360RFN Natural Gas Comfort Control 30,000
20,000
DV360RFP
Propane
Comfort Control 30,000
21,000
DV580RN
Natural Gas
Millivolt Hi/Lo
38,000
26,500
DV580RP
Propane
Millivolt Hi/Lo
38,000
27,000
DV580EN
Natural Gas
24 Volt Hi/Lo
38,000
26,500
DV580EP
Propane
24 Volt Hi/Lo
38,000
27,000
DV580RFN Natural Gas Comfort Control 38,000
26,500
DV580RFP
Propane
Comfort Control 38,000
27,000
Gas Inlet and Manifold Pressures
Natural
LP (Propane)
Minimum Inlet Pressure
5.5” w.c.
11.0” w.c.
Maximum Inlet Pressure
14.0” w.c.
14.0” w.c.
Manifold Pressure
3.5” w.c.
10.0” w.c.