Справочник Пользователя для Mitsubishi Electronics pha-a-kal

Select unit number 00

Mode

Settings

Mode no.

Setting no.

Initial setting

setting

Power failure automatic recovery

Not available

01

1

Available *1

2

Indoor temperature detecting

Indoor unit operating average

02

1

Set by indoor unit’s remote controller

2

Remote controller’s internal sensor

3

LOSSNAY connectivity

Not Supported

03

1

Supported (indoor unit is not equipped with outdoor-air intake)

2

Supported (indoor unit is equipped with outdoor-air intake)

3

Power voltage

230 V

04

1

208 V

2

Select unit numbers 01 to 03 or all units (AL [wired remote controller]/07 [wireless remote controller])

Mode

Settings

Mode no.

Setting no.

Initial setting

setting

Filter sign

100Hr

07

1

2500Hr

2

No filter sign indicator

3

Fan speed

Silent

08

1

–

Standard

2

High ceiling

3

–

*1 When the power supply returns, the air conditioner will start 3 minutes later.

X After completing installation and the wiring and piping of the indoor and 

X Use a 500-volt megohmmeter to check that the resistance between the 

X Do not carry out this test on the control wiring (low voltage circuit) 

The following 3 methods are available.

1

 Turn on the power at least 12 hours before the test run.

2

 Press the [TEST] button twice. ” “TEST RUN” liquid crystal display

3

 Press the [Mode selection] button. ” Make sure that wind is blown out.

4

 Press the [Mode selection] button and switch to the cooling (or heating) mode. 

  ” Make sure that cold (or warm) wind is blown out.
5

 Press the [Fan speed] button. ” Make sure that the wind speed is switched.

6

 Check operation of the outdoor unit fan.

7

 Release test run by pressing the [ON/OFF] button. ” Stop

8

 Register a telephone number.

  The telephone number of the repair shop, sales office, etc., to contact if an 

error occurs can be registered in the remote controller. The telephone number 
will be displayed when an error occurs. For registration procedures, refer to the 
operation manual for the indoor unit.

1

 Turn on the power to the unit at least 12 hours before the test run.

2

 Press  the 

TEST RUN

 button twice continuously.

  (Start this operation from the status of remote controller display turned off.)

A

 

 and current operation mode are displayed.

3

 Press  the 

MODE

 

 button to activate 

COOL

 mode, then check whether 

cool air is blown out from the unit.

4

 Press  the 

MODE

 

 button to activate 

HEAT

 mode, then check whether 

warm air is blown out from the unit. 

5

 Press  the 

FAN

 button and check whether fan speed changes.

6

 Press  the 

VANE

 button and check whether the auto vane operates properly.

7

 Press the ON/OFF button to stop the test run.

Note:
•  Point the remote controller towards the indoor unit receiver while following 

steps 2 to 7.

ON/OFF

  TEMP

FAN

VANE

TEST RUN

AUTO STOP

AUTO START

h

min

LOUVER

MODE

CHECK

RESET

SET

CLOCK

5

7

A

3,4

2

6

°F

°F

SIMPLE

PAR-21MAA

ON/OFF 

FILTER

CHECK

OPERATION

CLEAR

TEST

TEMP.

MENU

BACK

DAY

MONITOR/SET

CLOCK

ON/OFF

TEST RUN
COOL, HEAT

A

F

C

E

D B

M

I

HG

A

 ON/OFF button

B

 Test run display

C

 Indoor temperature liquid 

line temperature display

D

 ON/OFF lamp

E

 Power display

F

 Error code display

 

Test run remaining time 
display

G

 Set temperature button

H

 Mode selection button

I

 Fan speed button

M

 TEST button