Справочник Пользователя для Slant/Fin VSPH-60

20

Safe lighting and other performance criteria were met when

testing various gas manifold and control assemblies used

on the Victory VSP Series Boilers under the ANSI Z21.13-

latest edition.

Follow  the lighting instructions in this manual. These 

instructions are also attached to the boiler.

For Your Safety Read Before Operating

A. This appliance is equipped with an ignition device which

automatically lights the pilot. DO NOT try to light the pilot by

hand.

B. BEFORE OPERATING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

•  DO NOT try to light any appliance.

• DO NOT touch any electric switch: DO NOT use any

phone in your building.

•  Immediately call you gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire depart-

ment.

C. Use only your hand to turn the gas control knob. Never 

use tools. If the knob will not turn by hand, don’t try to 

repair it, call a qualified service technician. Force or 

attempted repair may result in a fire or explosion.

D. Do Not use this appliance if any part has been under 

water. Immediately call a qualified service technician to 

inspect the appliance and to replace any part of the 

control system and any gas control which has been under 

water.

1. STOP! Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device which

automatically lights the pilot. DO NOT try to light the pilot by

hand.

5. Remove jacket front panel

6. Turn gas control knob clockwise            to “OFF”.

DO NOT force.

7. Wait five (5) minutes (longer for propane) to clear out any 

gas, then smell for gas, including near the floor. If you then 

smell gas, STOP! Follow “B” in the safety information 

above on this page. If you don’t smell gas, go to next 

step.

8.

Turn as control knob counterclockwise            to “ON”.

9.

Replace jacket front panel.

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instructions 

“To Turn Off Gas to Appliance” and call your service 

technician or gas supplier.

1.

Set thermostat to lowest setting.

2.

Turn off all electric power to the appliance if service 

is to be performed.

3.

Remove jacket front panel.

4.

Turn gas control knob clockwise             till knob stops, 

then continue to “OFF”. Do not force.

5.

Replace jacket front panel.

Removing Jacket Front Panel
1.

Turn black screws 

1

⁄

4

turn to open position.

2.

Remove front panel.

To replace the panel, reverse procedure.

1.

Consult gas supplier for higher heating value* of gas 

(Btu/cu. ft.)

2.

Set thermostat high enough so that boiler will remain on 

3.

Measure manifold pressure.

Correct manifold pressure for gas used is printed on boiler 

rating plate. NOTE: Gas pressure may be adjusted by 

turning pressure regulator screw on combination gas valve 

(turn clockwise to increase pressure, counterclockwise to 

decrease pressure).

*  ”Higher Heating” value of gas is commonly known as “heating value”.

WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property

damage, personal injury or loss of life.

0FF

0FF

ON

ON

HON EYWELL

HON EYWELL

 GAS

 GAS
INLET

INLET

GAS 

CON TRO L 

KNO B

GAS 

CON TRO L 

KNO B

SHO W N 

IN 

"O FF"

SHO W N 

IN 

"O FF"

PO SITI

ON

PO SITI

ON

OUTLET

OUTLET

VSP40-19

VSP40-19

FIGURE 

19

FIGURE 

19