Справочник Пользователя для Regency U37-LP1
U37-1 Regency
®
ULTIMATE Rear Vent Direct Vent Freestanding Gas Stove
11
INSTALLATION
RIGID PIPE VENTING - VERTICAL TERMINATIONS
FOR BOTH RESIDENTIAL & MANUFACTURED HOMES/MOBILE HOMES
Offset to Vertical Terminations
Vertical Terminations
with Co-linear Flex System
The shaded area in the diagram shows the allowable vertical
terminations installed in a masonry chimney. All vertical vent instal-
lations require the Vent Restrictor to be set to 1-1/4" (32mm) open.
terminations installed in a masonry chimney. All vertical vent instal-
lations require the Vent Restrictor to be set to 1-1/4" (32mm) open.
Vertical Terminations
using Rigid Piping Systems
The shaded areas in the two diagrams below show all allowable
combinations of straight vertical and offset to vertical runs with
vertical terminations. Maximum one 90
combinations of straight vertical and offset to vertical runs with
vertical terminations. Maximum one 90
o
elbow. All vertical and
offset to vertical vent installations require Vent Restrictor to be set to
1-1/4" (32mm) open. If the vent is ENCLOSED in a chase (min. size
9" x 9") maintain a 1-1/4" (32mm) clearance to combustibles.
1-1/4" (32mm) open. If the vent is ENCLOSED in a chase (min. size
9" x 9") maintain a 1-1/4" (32mm) clearance to combustibles.
Straight Vertical Terminations
Vent Restrictor Position
Vent restriction is required for
certain venting installations,
see the diagrams in "Venting
Arrangment" section to deter-
mine if they are required for your
installation.
certain venting installations,
see the diagrams in "Venting
Arrangment" section to deter-
mine if they are required for your
installation.
To set the Vent restriction as
indicated in the diagram, simply
loosen the screws and push the
vent restrictor plate to the correct
position. Tighten the screws.
indicated in the diagram, simply
loosen the screws and push the
vent restrictor plate to the correct
position. Tighten the screws.
If using a Rigid Pipe Venting Sys-
tem a rigid pipe adaptor #640-994
is required.
tem a rigid pipe adaptor #640-994
is required.
Rigid Pipe
Adapter
This product has been evaluated by Intertek for
using a Rigid Pipe Adaptor in conjunction with
Duravent Direct-Vent GS, Selkirk Direct-Temp,
Ameri Vent Direct venting and Security Secure
Vent systems. Use of these systems with the
Rigid Pipe adaptor is deemed acceptable
and does not affect the Intertek WHI listing of
components.
using a Rigid Pipe Adaptor in conjunction with
Duravent Direct-Vent GS, Selkirk Direct-Temp,
Ameri Vent Direct venting and Security Secure
Vent systems. Use of these systems with the
Rigid Pipe adaptor is deemed acceptable
and does not affect the Intertek WHI listing of
components.
WARNING:
Do not combine venting components from
different venting systems.
different venting systems.
However use of the the AstroCap
TM
and FPI
Riser is acceptable with all systems.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCap
TM
and FPI Riser Vent terminal are
certifi ed for installations using FPI venting systems
as well as Simpson Dura-Vent
as well as Simpson Dura-Vent
®
Direct Vent GS,
American Metal Products Ameri Vent Direct Vent,
Security Secure Vent
Security Secure Vent
®
, Selkirk Direct-Temp. Astro-
Cap
TM
is a proprietary trademark of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct
Vent GS are registered and/or proprietary trademarks
of Simpson Dura-Vent Co. Inc.
Vent GS are registered and/or proprietary trademarks
of Simpson Dura-Vent Co. Inc.