Справочник Пользователя для Shark V1510

Fig.8

Always unplug the unit from 

electrical outlet before opening the Dust 
Cup (container).

Do NOT use the HEPA 

filter cartridge without the debris screen 
in place.

: After each Use - Always 

remove the filter debris screen from the 
HEPA  dust cup filter, then vigorously 
“TapClean” HEPA filter until no more 
dust can be removed.

IMPORTANT, Please Note : The 
“TapClean” HEPA dust cup filter & debris 
screen will stop most of the tiniest dust 
particles and airborne allergens from re-
entering the air you breathe. Because of 
this incredible filtration performance, the 
HEPA dust cup filter will quickly 
accumulate, inside the white filter folds, 
many fine dust particles that are difficult 
to see but which will eventually block or 
reduce your suction power - if not 
cleaned properly. Clean the HEPA filter 
and debris screen after each use as 
described in this section.
1. To remove the dust cup (container), 

hold the unit in the upright position to 
prevent the dust from falling out of the 
dust cup. (Fig. 6)

3. Rotate the lower dust cup clockwise 

to separate it from the filter 
chamber.  Empty and clean the dust 
cup.  (Fig. 8)

Fig. 6

2. To open the dust cup (container), 

push button and remove the dust 
cup (container ). (fig. 7) 

Fig.7

4. Remove the HEPA filter from the 

filter chamber. (Fig. 9)

5. Separate the debris screen from the 

HEPA filter cartridge by grasping the 
debris screen with one hand and the 
filter frame with the other and pull 
apart. (Fig. 10)

Fig. 9

Fig. 10

Fig. 11

6. Vigorously “TapClean” 

the HEPA dust cup 
filter on a hard 
surface until no more 
dust is observed 
falling out from 
between the pleats of 
the filter. (Fig. 11)

Fig. 12

Debris

Screen

7. “TapClean” the debris 

screen or rinse under 
a faucet until clean. 
(Fig. 12) Remember 
that the debris screen 
must be completely 
dry before reinstalling 
in the vacuum.

8. Replace the debris screen on the 

HEPA dust cup filter and reinstall 
filter assembly in the vacuum. (Not 
shown)

PLEASE NOTE: The white pleated 
filter material in the HEPA dust cup 
filter will discolor over time -This is 
NORMAL and will NOT affect the 
performance of the filter. If the HEPA 
dust cup filter 
is properly 
"TapCleaned” 
after each use 
and suction 
does not return 
to 100%, then 
we suggest that 
the HEPA filter 
be “TapCleaned”
vigorously until no
more dust can be removed, then 
rinsed under the faucet and allowed to 
dry for 24 hours before refitting into 
the vacuum. (Fig. A)  This should be 
done once a month or when 
suction appears reduced. 

: The suction hole must be 

open and free of any obstructions at 
all times.  Otherwise, the motor will 
overheat and could become 
damaged.

Fig. A

Wash once a 
month or when 
suction 
appears 
reduced.
.

Allow 24 

hours for drying before 
replacing in unit.

IMPORTANT:

This unit is equipped 

with a motor protective thermostat.  If 
for some reason the vacuum cleaner 
should overheat, the thermostat will 
automatically turn the unit off.  Should 
this occur:

• Push the On/Off button once.
• Disconnect the plug from the 

power source.

• Check the source of overheating 

problem. (i.e. clogged hose or 
filter)

• If clogged hose or filter is found, 

unclog the hose and replace the 
filters.

• Wait at least 45 minutes before 

attempting to reuse the vacuum.

• After unit has cooled down for 

45 minutes, plug in the cleaner 
and push the On/Off button. The 
vacuum should start again.

• If the vacuum still does not start, 

contact customer service at 
1 (800) 798-7398.