Справочник Пользователя для Hoover Stick Vacuum
9
Secondary filter
➞
DIRT PORT
NOZZLE
How to clean
SECONDARY
FILTER
FILTER
2. Grasp cup and pull forward to
remove from cleaner.
remove from cleaner.
3. Remove filter from top of cup.
The motor is equipped with two sleeve bearings. These bearings contain
sufficient lubrication for the life of the motor. Therefore,
sufficient lubrication for the life of the motor. Therefore,
do not add
lubricant to either motor bearing.
Lubrication
If you have a problem
If a minor problem occurs, it usually can be solved quite easily when the
cause is found by using the check list below.
cause is found by using the check list below.
Problem:
Cleaner won’t run
Possible Cause:
Possible Solution:
1. Not firmly plugged in .................................. Plug unit in firmly.
2. No voltage in wall plug ............................... Check fuse or breaker.
3. Blown fuse/tripped breaker ........................ Replace fuse/reset breaker.
3. Blown fuse/tripped breaker ........................ Replace fuse/reset breaker.
Problem:
Cleaner suction low
Possible Cause:
Possible Solution:
1. Dirt cup full ................................................. Empty cup.
2. Filter clogged ............................................. Empty dirt cup and clean
2. Filter clogged ............................................. Empty dirt cup and clean
....................................................................... filter.
3. Nozzle clogged .......................................... Remove obstruction.
4. Speed selector (some models) .................. Push selector to high speed
set too low
4. Speed selector (some models) .................. Push selector to high speed
set too low
Problem:
Cleaner is difficult to push on carpet
Possible Cause:
Possible Solution:
1. Nozzle set for “BARE FLOOR“;
brush is locked ............................................ Set nozzle for “RUG”.
brush is locked ............................................ Set nozzle for “RUG”.
10
Rug and floor nozzle
To maintain the cleaning effectiveness of your deluxe nozzle or deluxe
wheeled nozzle, the brushes may need to be replaced occasionally.
See your nearest Hoover Factory Service Center or Authorized Warranty
Dealer (Depot) for new brushes.
wheeled nozzle, the brushes may need to be replaced occasionally.
See your nearest Hoover Factory Service Center or Authorized Warranty
Dealer (Depot) for new brushes.
4. Empty cup, making sure to hold
cup with dirt port facing up, and
shake dust from filter.
cup with dirt port facing up, and
shake dust from filter.
5. Push filter inside out through filter
frame.
frame.
The secondary filter protects the
motor from dirt particles and does
not need to be removed for cleaning.
The filter is located on the inside top
of the cleaner body and can be seen
when the dirt cup and filter are
removed. When the filter becomes
dirty, it can be cleaned by wiping it
off with a damp cloth.
motor from dirt particles and does
not need to be removed for cleaning.
The filter is located on the inside top
of the cleaner body and can be seen
when the dirt cup and filter are
removed. When the filter becomes
dirty, it can be cleaned by wiping it
off with a damp cloth.
Disconnect cleaner from
electrical outlet.
electrical outlet.
6. Brush surface of filter to remove
any clinging litter. (Filter may be
washed in warm water. It must be
any clinging litter. (Filter may be
washed in warm water. It must be
completely dry
before replacing in
cleaner. Do not use cleaner
without filter in place.)
without filter in place.)
Push filter back through frame
and pull it right side out.
and pull it right side out.
8. Slide filter into cleaner body and
latch cup into position.
latch cup into position.
7. Place filter
on top
of cup as
shown and push frame fully into cup.
Some models have a tab (A) on the
frame which fits down into a slot (B)
in the cup.
Some models have a tab (A) on the
frame which fits down into a slot (B)
in the cup.
A
B